Series framework
Stainless steel 2-piece ball valves
Full-port, two-piece body in 304 or 316L for water, oil, gas and corrosive liquids. Medium-duty and heavy-duty builds. Working frame: PN16, female thread. Formal price is always an RFQ — this page is the selection outline.
Key features
- 304 / 316L body (CF8 / CF8M)
- 2-piece body, full bore
- PTFE seats
- Lockable lever handle
- BSP, NPT, BSPT or G threads
- Install in any orientation
Technical specifications
| Body / ball | 304 or 316L stainless (CF8 / CF8M) |
|---|---|
| Seat / gasket | PTFE |
| Stem | 304 stainless steel |
| Handle | Stainless lever with plastic grip, lockable |
| Pressure | PN16 / 1.6 MPa (232 PSI) — confirm series on RFQ |
| Temperature | 0°C to 100°C typical; ask if media is outside this band |
| Threads | BSP, NPT, BSPT, G |
| Port | Full bore (full port) |
| Ends | Female thread |
| Operation | Manual 90° lever, bi-directional |
| Media | Water, oil, gas, corrosive liquids (alloy dependent) |
Construction
Smooth finish, even wall, machined seats. Heavy-duty series uses a thicker wall than medium-duty for tougher duty. Photos and an exploded drawing will replace this outline when the catalog shots are ready.
Main parts & materials
| No. | Part | Material |
|---|---|---|
| 1 | Body | SS 304 / 316L |
| 2 | End cap | SS 304 / 316L |
| 3 | Ball | SS 304 / 316L |
| 4 | Seat (2) | PTFE |
| 5 | Stem | SS 304 |
| 6–7 | Gland packing / thrust washer | PTFE |
| 8–10 | Gland nut, handle nut, spring washer | SS 201 |
| 11–13 | Handle, sleeve, locking device | SS 201 + plastic grip |
Two series
Series A — medium duty (304)
General water, oil and gas. Working pressure up to 1.6 MPa in the selection sheet.
Series B — heavy duty (304 / 316L)
Thicker wall for harder service and better corrosion resistance. Confirm the duty on the RFQ.
Size chart & typical MOQ
Prices are not listed. MOQ is a starting guide from the selection sheet and can be negotiated.
| Inch | DN | Guide MOQ (pcs) | Price |
|---|---|---|---|
| 1/8" | DN6 | 100 | On request |
| 1/4" | DN8 | 100 | On request |
| 3/8" | DN10 | 100 | On request |
| 1/2" | DN15 | 100 | On request |
| 3/4" | DN20 | 100 | On request |
| 1" | DN25 | 50 | On request |
| 1-1/4" | DN32 | 50 | On request |
| 1-1/2" | DN40 | 50 | On request |
| 2" | DN50 | 50 | On request |
| 2-1/2" | DN65 | 20 | On request |
| 3" | DN80 | 20 | On request |
| 4" | DN100 | 20 | On request |
Ordering
- Delivery: about 5–7 days for stocked items; about 15–25 days for bulk / make-to-order.
- Payment: T/T (typical 30% deposit, balance before shipment) or L/C at sight — confirmed on the quotation.
- Packing: bag + inner carton + export carton; wooden case for large lots.
- Shipping: FOB Shanghai or Ningbo, or the Incoterm you specify.
- Quotation validity: about 30 days unless the reply says otherwise.
More on delivery andquality. Instrumentation-style compression ball valves stay in theball valve category.
Questions on this valve
Why a two-piece body rather than three-piece?
A two-piece body splits once, so the ball and seats can be reached by opening that joint. A three-piece body takes the centre section out between two unions, which means the pipe stays put; the two-piece is shorter and cheaper for the same bore.
Can I service the seats without cutting the pipe?
Only to the extent the joint allows. The body opens, but the valve still has to be broken out of the line on one side. Where the line must stay intact, a three-piece body is the one to specify.
What does PN16 mean in working terms?
PN16 is 1.6 MPa, about 232 psi, at the reference condition. The figure is a class, not a promise at every temperature, so state the medium and the working temperature with the RFQ and the answer comes back for that duty.
What temperature can the standard seat take?
The PTFE seat puts typical service at 0-100 °C. Above that the seat is the limit rather than the body, and the question becomes whether a different seat material is available for the duty.
Full port or reduced bore?
This range is full bore, so the ball passage matches the pipe bore and the valve adds little pressure drop. A reduced bore is smaller and cheaper but throttles the line permanently.
Which thread forms are offered?
BSP, NPT, BSPT and G. They are not interchangeable — an NPT male will start in a BSP female and then leak — so name the form on both the valve and the mating part.