HS codes for stainless steel fittings sit in heading 7307; stainless valves sit in heading 8481. That six-digit decision follows your goods across every border: it sets the duty rate, drives clearance speed and anchors the paperwork trail.
The quick answer: declare a code per line, extend it into your destination’s national tariff, and keep the same code on the invoice, packing list and certificate of origin.
Key takeaways
- Stainless tube and pipe fittings live in heading 7307: 7307.21 flanged, 7307.22 threaded elbows/bends/sleeves, 7307.23 butt-welding fittings, 7307.29 everything else stainless — cast bodies enter at 7307.11/7307.19.
- Valves live in heading 8481: 8481.30 check valves, 8481.20 pneumatic/hydraulic transmission valves, 8481.10 pressure-reducing, 8481.40 safety/relief — and ordinary ball, gate and needle valves land in the catch-all 8481.80.
- The 6-digit HS level is international, but duty rates and extra digits are national: your destination country extends codes to 8–10 digits with its own tariffs, and final classification is legally the importer’s responsibility.
Which code do I declare?
Read down the family, take the code, then check the last column: it names the property that decides the subheading when a part sits between two lines.
| Product family | HS heading / code | Note for importers | What decides the subheading |
|---|---|---|---|
| Stainless flanges | 7307.21 | Flanged fittings of stainless steel; verify forged-vs-other splits at national level | Connection type: flanged |
| Stainless threaded elbows, bends, sleeves | 7307.22 | Threaded compression bodies and adapters typically land here | Connection type: threaded |
| Stainless butt-welding fittings | 7307.23 | Weld-end fittings and weld unions | Connection type: weld end |
| Other stainless fittings (unions, tees, nipples, compression bodies n.e.s.) | 7307.29 | The residual stainless line — most catalogue fittings settle here | Connection type: none of the above |
| Cast fittings of iron/steel | 7307.11 / 7307.19 | Investment-cast bodies enter under the cast-fittings lines | How the body is made: cast, not wrought |
| Check (non-return) valves | 8481.30 | Spring, swing and dual-plate checks | Valve function: non-return |
| Valves for pneumatic/hydraulic transmission | 8481.20 | Directional and flow-control valve stations | Valve function: transmission control |
| Pressure-reducing valves | 8481.10 | Regulators | Valve function: reduction |
| Safety or relief valves | 8481.40 | Overpressure protection | Valve function: overpressure protection |
| Other valves — ball, gate, globe, needle | 8481.80 | The catch-all: most manual ball and needle valves classify here | Valve function: manual shut-off |
| Valve parts | 8481.90 | Repair kits and loose internals | What you ship: parts, not a complete valve |
| Corrugated flexible hose assemblies | Heading 8307 territory | Flexible tubing of base metal, with or without fittings; exact classification depends on construction and end fittings — confirm with your broker | Construction and end fittings |
The split inside each heading is mechanical. A fitting takes its subheading from how it connects: the same stainless elbow is 7307.22 threaded and 7307.23 butt-welding. A valve takes its subheading from what it does, not from its body material, so a check valve and a ball valve of the same stainless grade land in different lines.
Cast bodies are a separate question, not a sub-choice of the connection type. The 7307.11 and 7307.19 lines exist because foundry products classify apart from machined barstock, so an investment-cast body is asked for as cast, whatever its ends.
The hose row is deliberately cautious. Flexible assemblies classify by construction and by what is on each end rather than by the fitting style, so the heading is given and the six-digit decision belongs to your broker.
Is six digits enough for my country?
Six digits is the international level; your destination extends it. The US HTS and the EU CN add subdivisions, taking the code to 8–10 digits, and those subdivisions carry their own duty rates.
In the US schedule, 7307.21 carries national subdivisions by forging state — 7307.21.10 against 7307.21.50. Quote the heading to your supplier, but declare the national code.
Final classification is legally the importer’s responsibility, not the factory’s or the forwarder’s. A factory can advise from export experience; the import declaration is yours, and so is the duty consequence.
Why does the code matter to the shipment?
Three things follow from the code: what you pay, how fast the shipment clears, and whether the paperwork agrees with itself.
Duty. Headings and subheadings carry different percentages. Misclassify and you either overpay, or take a retroactive bill with penalties.
Clearance. A correct, consistently used code lets customs process the declaration routinely. An ambiguous or missing one routes the shipment to inspection.
Paperwork. Certificates of origin, preference claims under trade agreements and the factory’s export declaration all key off the same code. When invoice, packing list and certificate disagree, clearance stops.
Keep it consistent on all three documents; mixed codes for identical goods are an audit invitation. Material certificates ride the same wave: the EN 10204 3.1 guide covers the certificate types and how to name them on the RFQ.
What goes wrong at customs, and what do I change?
Almost every hold traces back to one document disagreeing with another, or to a code taken from habit rather than from the goods.
| Symptom | Most likely cause | What to change |
|---|---|---|
| Shipment routed to inspection on arrival | Code missing, ambiguous, or different from the one on the certificate | One code per line, and every document generated from it |
| Duty re-assessed after release | Declared heading does not match how the part connects or what the valve does | Classify fittings by connection type, valves by function |
| Certificate of origin queried | Its code differs from the code on the invoice | Correct the document that drifted, then re-issue the set |
| Preference claim refused | Claim keyed to the heading, not to the destination’s national code | Key the claim to the national subdivision you declare |
| Identical goods cleared under two codes | Two shipments classified by different people, nothing written down | One written classification per part number, reused |
| Hose assembly challenged | Classified as a 7307 fitting because of its end fittings | Heading 8307 territory: construction and end configuration decide |
| Invoice and packing list disagree | The code was typed onto one document by hand | Generate both from the same line item |
The pattern holds in every row: the code is a property of the line item, not a decoration added to a document. Fix it where the line item lives.
How do I put the code on the RFQ?
A code that reaches the factory late, or only on the purchase order, is a code the export documents will contradict.
- Name the family and the connection. Flange, thread, weld end, or none of these — that is what moves a fitting between 7307.21, 7307.22, 7307.23 and 7307.29.
- Name the valve function. Check, pressure-reducing, safety or relief, transmission, or manual shut-off. Function, not body material, picks the 8481 line.
- Separate cast from wrought. An investment-cast body is asked for as cast, so the quotation carries 7307.11 or 7307.19.
- State the destination country. It fixes the national extension, and it fixes any preference claim you intend to make.
- Ask for the code per line on the invoice, with the packing list and certificate of origin generated from those same lines.
Before it goes on the RFQ:
- Product family and connection type — flange, thread, weld end, other.
- Valve function — check, pressure-reducing, safety or relief, transmission, manual shut-off.
- Cast or wrought body.
- Destination country, and the national code you expect.
- Whether a preference claim is intended.
- One line list, one quote.
FerruleX’s export invoices state the agreed codes per line, with packing lists and certificates aligned to them — see the products hub for the catalogue families and the downloads page for documentation samples.
Send your destination country and expected code context with the RFQ, and we quote with paperwork that matches your import side. Request a factory quote.
FAQ
What HS code do stainless steel compression fittings use? Heading 7307, most commonly 7307.29 for other stainless fittings; threaded bodies often classify at 7307.22. The six digits follow the connection type, and your destination extends the code further.
What is the HS code for stainless ball valves? Heading 8481, catch-all 8481.80 for ordinary manual ball valves. Check valves take 8481.30, safety and relief valves 8481.40, and valve parts 8481.90.
Do HS codes differ by country? The six-digit level is international. Beyond it each country extends the code in its own tariff — the US HTS and the EU CN add subdivisions with different duty rates. Verify the destination tariff, not just the heading.
Who is responsible for correct classification? The importer of record, legally. Factories and forwarders advise from experience, but the import declaration and any duty consequences belong to the buyer.
Why should the code go on the RFQ? So the invoice, packing list and certificates match your import declaration from the start. Consistent codes mean routine clearance; mixed or missing codes mean inspection, delay and re-assessed duty.



