Skip to content

Need stainless steel fittings, valves or hose?

The Dash Size Chart: How -4 to -32 Notation Maps to Real Dimensions

Dash size chart: how -4 to -32 dash numbers map to fractional inch and millimeter tube sizes in SAE/JIC hydraulic fittings, and how to read a spec line.

Sep 27, 2026 · 4 min read · FerruleX Factory

Stainless male-to-female straight adapter converting between thread and tube ends

A dash size is a shorthand number that says how big a hydraulic tube or hose end is, in sixteenths of an inch: the dash number divided by 16 gives the size.

It is the sizing language of SAE and JIC fittings and adapters, and once you can read it, a spec line like “6-6 STR JIC” tells you both ends at a glance.

So a -4 is 4/16 (1/4 inch, 6.35 mm), a -6 is 3/8 inch, and a -8 is 1/2 inch. The chart below covers every common dash from -4 to -32. The fault table further down covers the mistakes that still cost buyers a re-order.

Key takeaways

  • Dash size = the fitting or tube size in 16ths of an inch: -4 is 4/16 (1/4 inch, 6.35 mm), -6 is 6/16 (3/8 inch), -8 is 1/2 inch, and -32 is 2 inches (50.8 mm).
  • On SAE/JIC tube fittings the dash number corresponds to the tube outside diameter; on hose ends it commonly denotes the hose inside diameter.
  • Dash notation belongs to the SAE/JIC world — it is not an NPT pipe size. A -4 NPT port does not have a 1/4 inch thread; pipe threads are identified from an NPT thread chart.
  • Read a spec line end by end: “6-6” means 3/8 inch (dash -6) on both ends of the adapter or hose assembly.

Which dash size do I need?

The dash number comes from the tube or the hose, not from a thread you measured on the part. On SAE/JIC tube fittings the dash corresponds to the tube outside diameter; on hose ends it commonly denotes the hose inside diameter. Read the table before you open a catalogue.

Where the dash appears What it refers to Decisive check
SAE/JIC tube fitting Tube outside diameter Measure tube OD at the end, then read the dash
Hose end Hose inside diameter Measure hose ID; the dash is not the fitting hex
NPT port Nothing — dash is not an NPT size Take the size from an NPT thread chart
Metric tube on a mixed panel A near-miss label, not a conversion State the metric OD and the dash together

One column decides it: the measurement taken off the actual tube or hose. A -6 fitting is made for 3/8 inch tube OD, and nothing you measure on the fitting body changes that.

What do the dash numbers mean in inches and millimetres?

The arithmetic is the whole trick: divide the dash number by 16. That is why -12 (12/16) is 3/4 inch and -16 is a full inch, and why the jump from -16 to -32 doubles the size.

Dash Fractional inch mm Typical use
-4 1/4 inch 6.35 Small instrument and pilot lines
-6 3/8 inch 9.53 The workhorse instrument tube size
-8 1/2 inch 12.70 Instrument and hydraulic mains on skids
-10 5/8 inch 15.88 Medium hydraulic lines
-12 3/4 inch 19.05 Process and hydraulic distribution
-14 7/8 inch 22.23 Less common; larger instrument runs
-16 1 inch 25.40 Hydraulic supply and return lines
-20 1-1/4 inch 31.75 Larger hydraulic and process runs
-24 1-1/2 inch 38.10 Manifold and station feeds
-28 1-3/4 inch 44.45 Rare; special machinery runs
-32 2 inch 50.80 Large-bore hose and tube headers

Millimetre users can read the same chart straight across: the mm column is the verified inch value converted. It is also the cleanest way to talk to a metric-drawing shop about a fractional-drawing line.

The reverse conversion discipline is covered in metric vs fractional tube sizes. A printable version of this chart lives on our dash size chart sheet.

How do I read a dash spec line?

Adapter and hose drawings stack the dash numbers end to end: first end, then second end. Read the call-out in that order and it resolves into a part you can check.

  1. Split the pair. In a “6-6 straight adapter” the first number is one end and the second number the other.
  2. Divide each number by 16. A “6-6” is 3/8 inch on both ends; a “6-8” steps from 3/8 inch to 1/2 inch.
  3. Read the end geometry after the number. A “-6 JIC” call-out means a 3/8 inch tube-size fitting with a 37° flare seat.
  4. Match the tube to the number. A -6 fitting is made for 3/8 inch tube OD; matching tube to number, not to a thread measurement, is what keeps the joint honest.
  5. Stop where a pipe thread starts. When the second end is a pipe thread the drawing says so explicitly, and that is where dash notation ends and pipe-thread charts begin.

The number describes the fitting’s size in the SAE/JIC system. It is a nominal code for the tube or hose it serves, not a measurement of the fitting body.

Why did my adapter arrive one size off?

Most dash-size errors are a system mix-up rather than a machining fault. The symptom shows at assembly, when the port and the adapter disagree by one step.

Symptom Most likely cause What to change
Adapter sits one size off at the port The dash was read as an NPT size Take the port size from an NPT thread chart, not from dividing a dash
Hex or thread does not match the dash ordered The dash was treated as the measured fitting size Size hex and thread from the standard governing the end form
Part arrives built to the wrong system A mixed metric and fractional panel was ordered by dash alone Put the metric OD (6, 8, 10 or 12 mm) and the dash on the same line

Mixing the two systems is the most common reason an adapter arrives one size off. The identification method for the pipe side is covered in NPT vs G (BSP) threads.

What do I put on the RFQ?

Give the factory what the drawing gives you: end form, dash size and, where a pipe thread is involved, the thread call-out.

  • End form for each end, with the 37° flare noted where the drawing calls it.
  • Dash size for each end, first end then second end.
  • Thread call-out wherever a pipe thread replaces a dash.
  • Material, for example 316 stainless.
  • Metric OD alongside the dash when the tube itself is metric, and both systems stated when the panel mixes them.

“6-6 straight adapter, both ends -6 JIC, 316 stainless” is a complete line. “8-4 reducer, -8 JIC to -4 NPT male” is complete in the same way: direction, thread call-out and material all appear in the string.

FerruleX supplies the stainless adapters that live at the dash-to-thread boundary of these drawings. See the adapters and weld category for straight, elbow and reducing adapters, and the products hub for the fitting families they connect.

Send the spec line as drawn and we match both ends. Request a factory quote.

FAQ

What does a dash number mean on a hydraulic fitting? The size in sixteenths of an inch: divide the number by 16. A -4 is 1/4 inch, -6 is 3/8 inch, -8 is 1/2 inch, -32 is 2 inches. Tube fittings read tube OD; hose ends read hose ID.

Is a dash size the same as an NPT size? No. Dash sizing belongs to SAE/JIC tube and hose fittings; NPT is a pipe thread standard with its own size table. A fitting marked -4 on an NPT port does not have a 1/4 inch thread.

What size is a -6 fitting? 3/8 inch. The dash number over 16 gives 6/16 = 3/8 inch, which is 9.53 mm. A “-6 JIC” fitting is made for 3/8 inch tube OD with a 37° flare seat.

What is the biggest common dash size? -32, or 2 inches (50.8 mm), is the top of the standard dash chart and appears on large-bore hose and tube headers. The everyday instrument range is -4 through -12.

How do I convert a dash size to millimetres? Divide by 16 for inches, then multiply by 25.4. A -12 is 12/16 inch = 3/4 inch = 19.05 mm. Metric near-misses such as 6 mm versus 1/4 inch are not interchangeable: state the system on the RFQ.

Related articles

More guides for stainless steel fittings buyers.