Skip to content

Need stainless steel fittings, valves or hose?

Metric vs Fractional Tube Sizes for Compression Fittings

Metric compression fittings vs fractional inch tube sizes: the conversion table, why 6 mm is not 1/4 inch, and how to avoid mixed-system ordering mistakes.

Sep 25, 2026 · 5 min read · FerruleX Factory

Compression reducing union joining two different tube outside diameters

Metric compression fittings and fractional-inch tube are two separate catalogues, both sized by tube outside diameter.

They look interchangeable and they are not. 1/4 inch tube is 6.35 mm, 3/8 inch is 9.53 mm and 1/2 inch is 12.70 mm — close to 6, 10 and 12 mm, but no pair in the two series matches. Measure the tube and read the fitting stamp before you order.

Key takeaways

  • Compression fittings are sized by tube outside diameter, and fractional and metric series are separate catalogs: 1/4 inch is 6.35 mm, 3/8 inch is 9.53 mm, 1/2 inch is 12.7 mm — close to 6, 10 and 12 mm, but no pair is interchangeable.
  • Ferrules are size-specific to a tenth of a millimeter: a metric ferrule on fractional tube (or vice versa) under- or over-bites, and the joint leaks no matter how carefully it is made.
  • Identify what you have before ordering: measure the tube OD with calipers and read the fitting stamp — then state the system, size and tube OD explicitly on the RFQ.

Which one do I need?

Start with the equipment, not the fitting catalogue. A panel drawn to a European or most Asian OEM convention runs metric tube, where 6, 8, 10 and 12 mm runs dominate. A North American panel runs fractional inches: 1/4, 3/8 and 1/2 inch.

Both catalogues are complete in their own system. Every body style, union, elbow and adapter exists in metric and in fractional, so the question is never what is available — it is what the panel already is.

Your situation Series to order What decides it
Panel built to a European or most Asian OEM Metric: 6, 8, 10, 12 mm runs The panel drawing, not catalogue availability
Panel built to a North American OEM Fractional: 1/4, 3/8, 1/2 inch The panel drawing, not catalogue availability
Replacing a ferrule or fitting on existing tube The series that matches the measured tube OD Caliper reading, taken to 0.01 mm
Joining a metric run to a fractional run Metric end plus fractional end, through an adapter A system-to-system adapter, never a forced ferrule
New project with no legacy tube One series for the whole project Spare-parts duplication and assembly errors

Why do the two systems coexist?

Regional OEM convention, inherited rather than chosen. European and most Asian equipment is drawn in millimetres; North American equipment is drawn in fractional inches.

Export buyers end up with both systems on the same plant. That is why mixed-system mistakes top the list of cross-border fitting errors.

The ferrule mechanics and the pressure classes are the same in both systems — see single ferrule vs double ferrule for that layer.

How close are the metric and fractional sizes?

Fractional OD Closest metric Actual mm Interchangeable?
1/8” 3 mm 3.18 mm No
1/4” 6 mm 6.35 mm No — the classic near-miss
3/8” 10 mm 9.53 mm No
1/2” 12 mm 12.70 mm No
5/8” 16 mm 15.88 mm No — closer still, still not
3/4” 18 / 20 mm 19.05 mm No
1” 25 mm 25.40 mm No

Even the closest pairs — 5/8 inch against 16 mm, 1 inch against 25 mm — differ by more than a tenth of a millimetre. That sounds like nothing until you remember how the joint works: the ferrule is engineered to swage one specific tube diameter.

A tenth of a millimetre of under- or oversize puts the bite in the wrong place. The joint assembles, feels snug and weeps at pressure — and the leak shows up on gas service first.

How do I tell which system I have?

Two checks settle it in a minute: measure the tube, read the fitting. Work in this order.

  1. Step 1 — Measure the tube. Calipers across the tube OD, away from the ferrule bite marks.
  2. Step 2 — Read the number. Values like 6.35, 9.53 and 12.70 mm are fractional signatures.
  3. Step 3 — Check for metric. 6.0, 10.0 and 12.0 mm are metric. Rounding to “about six” is the mistake that costs a reorder.
  4. Step 4 — Read the fitting. Bodies and nuts are stamped with the system and size — 6MM, 8MM, or 1/4, 3/8.
  5. Step 5 — Mark mixed runs. If the stamp is gone, the caliper reading is the answer. When a panel mixes systems, mark each run before ordering replacements.

Ferrule brands add another layer, and the no-mixing rule from the ferrule guides applies within a system too.

What happens if I mix them?

Symptom Most likely cause What to change
Joint assembles, feels snug, then weeps Metric tube in a fractional fitting, or the reverse Re-fit the tube’s own system; the bite is size-specific
Leak appears on gas service first The same mixed bite, a tenth of a millimetre out Change the fitting to the tube system, not the closest size
Nut will not start on the tube 6 mm fitting on 1/4 inch tube, or a fractional fitting a size small Read the stamp, then check the measured OD
Replacement order arrives wrong Tube OD rounded to “about six” Put the measured OD and the series on the RFQ
Correct-size joint still leaks A ferrule from another brand on the body Keep one ferrule brand with its body, inside one system

How do I order the right one?

State the system, the size and the tube OD in the fitting’s own language — “10 mm compression union, both ends” or “3/8 inch tube × 1/2 NPT male connector”. If the two ends of one fitting differ, name both.

Check the RFQ against this before it leaves:

  • System — metric or fractional, written out.
  • Size — the nominal size in that system.
  • Tube OD — the measured value, not a rounded one.
  • End connections — both ends, where they differ.
  • Material.
  • System transitions on the same skid, stated explicitly.

If you are converting between systems on one skid, say so. We quote proper adapters rather than letting the mismatch hide in the BOM. If the tube itself is unmarked and of unknown origin, send the OD measurement — the system can be identified from it.

FerruleX stocks compression fittings in both metric and fractional series — straight unions and reducing unions bridge sizes within a system, and mixed-system adapters bridge between them. Send tube OD, system, material and end connections, and we quote the stocked size. Request a factory quote.

FAQ

Is 6 mm tube the same as 1/4 inch? No. 1/4 inch is 6.35 mm, three tenths of a millimetre larger than 6 mm. A 1/4 inch fitting under-bites on 6 mm tube and leaks; a 6 mm fitting will not accept 1/4 inch tube.

Can I mix metric and fractional fittings on one panel? Yes, if each joint matches its own tube’s system and system-to-system transitions use proper adapters. Never force one system’s ferrule onto the other system’s tube; the bite geometry is size-specific.

Which system should I standardize on for a new project? Match the equipment convention: metric for European and most Asian OEM skids, fractional for North American. One system per project avoids spare-parts duplication and assembly errors; mixing to save a line item is false economy.

How do I measure tube OD accurately? Digital calipers across the tube end, away from the ferrule bite marks, read to 0.01 mm. Compare against the table: 6.35, 9.53 and 12.70 mm are fractional; 6.0, 10.0 and 12.0 mm are metric.

What if my fitting has no size stamp? Measure the tube OD it was made for — the fitting follows the tube. If the tube is gone too, measure the ferrule bore or the nut’s tube entry with calipers and compare against the table.

Related articles

More guides for stainless steel fittings buyers.