
Compression Reducing Union — 316L, Many Sizes
Compression Reducing Union: stainless steel compression fittings joining unequal tube OD. SS316/304. FerruleX RFQ. Stocked sizes ship fast. Fast stock shipping.
- Brand
- FerruleX
- Material
- SS316 / SS316L / SS304
- Tube OD
- 3–25 mm / 1/8"–1", unequal pair
- Type
- Straight reducing union, tube to tube
- Pressure
- 1000 psi standard / 4500 psi high-pressure
- Stock5–7 days after confirmation
- Make to order15–25 days production
- Payment / termsT/T ~30% or L/C · FOB Shanghai / Ningbo
- OEMLogo and drawings accepted · price on RFQ
Description
A reducing union joins two tube lines of different outside diameter in one straight body, so a metric line can hand over to a fractional one without an adaptor. Each end is a standard two-ferrule bite joint — body, ferrule, nut — and both tubes grip on their own ferrule. The part number is the pair of tube sizes, not a thread: a 12 mm to 6 mm joint is ordered as 12 × 6, and both ODs belong on the RFQ, larger size first, so purchasing and the factory read the same reducing direction. Pairs sit inside the 3–25 mm and 1/8"–1" envelope in 316, 316L or 304. Both tubes must be fully annealed, below HRB 90 / HV 190, to ASTM A269 or GB/T 14976, and inserted until they bottom in the body.
Straight reducing union for two different tube outside diameters, 3–25 mm and 1/8–1 in. Order by both ODs — the pair is the part number. Two-ferrule bite joint in 316, 316L or 304 stainless, standard series to 1000 psi. State the larger OD first so the reducing direction is unambiguous.
- Step-down
- One body joins the larger line to the smaller, without an adaptor.
- Part number
- The two tube ODs are the specification; both go on the RFQ.
- Annealed tube
- Both tubes fully annealed, below HRB 90 / HV 190, per A269 or GB/T 14976.
- Rating
- 1000 psi standard, 4500 psi high-pressure; table range -40 to 150 °C.
Specifications
| Specification | Value |
|---|---|
| Brand | FerruleX |
| Material | SS316 / SS316L / SS304 |
| Tube OD | 3–25 mm / 1/8"–1", unequal pair |
| Type | Straight reducing union |
| Order form | Both tube ODs, larger size first |
| Pressure | 1000 psi standard / 4500 psi high-pressure series |
Request Quote
Prices stay on the RFQ. Send size, material, quantity and destination — the factory replies with price, lead time and packing. Packing, payment and the usual quote questions are on thedelivery pageand the FAQ.
Questions about this part
How should the tube ends be prepared before the fitting goes on?
Cut square and deburr both ends, inside and out, then wipe them clean. A burr or a deep score mark under the ferrule will not seal however hard the nut is turned.
How far does each tube enter the body?
Push each tube in until it bottoms on the body shoulder, then mark the nut position before tightening. On a reducing body the two ends differ, so check each side separately.
Is the nut set by torque or by turns?
Finger tighten the nut, then bring it up by turns with a wrench while the body is held. Go by feel and the marked position rather than a torque figure, which varies with thread friction.
Can I reuse the ferrules when remaking the joint?
A first remake is acceptable if the tube was not scored and the ferrules still sit square in the body. Cut the tube back and fit a new ferrule pair when the old bite no longer lines up.
Can I use ferrules from another maker in this body?
Ferrule and body cone geometry differ between makers, so a mixed pair may bite at the wrong point on the tube. Keep the body, ferrules and nut as one matched set from the same maker.
The joint weeps as soon as pressure is applied. What should I check first?
Check that both tubes bottomed before tightening and that neither nut was backed off after the bite. A joint that weeps at once usually has a tube short of the shoulder or a ferrule never drawn down.
Related products

Compression Male Elbow Connector
Compression Male Elbow Connector: 90° stainless steel compression fittings, tube to male thread. FerruleX RFQ. Stocked sizes ship fast. Fast stock shipping.
View details →
Compression Union Elbow
Compression Union Elbow: 90° stainless steel compression fittings, tube-to-tube double ferrule. FerruleX RFQ. Stocked sizes ship fast. Fast stock shipping.
View details →
Stainless Steel Compression Male/Female Tee — Sizes
Compression Male/Female Tee: stainless steel compression fittings tee with thread branch options. FerruleX RFQ. Stocked sizes ship fast. Fast stock shipping.
View details →
Stainless Steel Compression Reducing Tee — Sizes
Compression Reducing Tee: stainless steel compression fittings with smaller branch take-off. FerruleX factory RFQ. Stocked sizes ship fast. Fast stock shipping.
View details →