Skip to content

Need stainless steel fittings, valves or hose?

Compression Male Elbow Connector — FerruleX stainless steel fittings

Compression Male Elbow Connector

Compression Male Elbow Connector: 90° stainless steel compression fittings, tube to male thread. FerruleX RFQ. Stocked sizes ship fast. Fast stock shipping.

Brand
FerruleX
Material
SS316 / SS316L / SS304
Tube OD
3–25 mm / 1/8"–1"
Threads
M5–M24 / NPT / G / R (BSPT)
Type
Male elbow, tube to male thread, 90°

Request a factory quote

  • Stock5–7 days after confirmation
  • Make to order15–25 days production
  • Payment / termsT/T ~30% or L/C · FOB Shanghai / Ningbo
  • OEMLogo and drawings accepted · price on RFQ

Description

The male elbow puts the tube and the male thread at 90°: compression joint on the tube side, threaded port on the equipment side, one body instead of an elbow plus a connector. That right angle sets two checks before ordering. Thread engagement decides where the tube leg points: with a tapered thread (NPT, R) the point where it seats is the orientation, and with a straight thread a sealing washer sets it — so check the port type, not just the thread size. Panel clearance decides whether the elbow body and nut fit behind the face, plus 10 mm of straight tube beyond the nut before any bend starts. Threads run M5–M24 and NPT, G or R (BSPT); tube 3–25 mm and 1/8"–1"; bodies in 316, 316L or 304. Orient the thread before the ferrule is pulled up, so the elbow is not fighting the port.

90° connector with a compression tube end and a male thread end, M5–M24 or NPT / G / R (BSPT), tube 3–25 mm and 1/8–1 in. Check thread engagement depth and panel clearance before ordering. 316 / 316L / 304 stainless, standard series to 1000 psi, 4500 psi high-pressure.

Engagement
Tapered thread: the seated point is the orientation. Straight thread: the washer face.
Clearance
Room for body and nut, plus 10 mm straight tube before the first bend.
Orientation
The 90° body fixes the tube exit, so plan the run before the port is drilled.
Threads
M5–M24 metric, NPT, G or R (BSPT); tube 3–25 mm and 1/8"–1".

Specifications

SpecificationValue
BrandFerruleX
MaterialSS316 / SS316L / SS304
Tube OD3–25 mm / 1/8"–1"
ThreadsM5–M24 metric, NPT, G, R (BSPT)
TypeMale elbow, 90°, tube to male thread
Pressure1000 psi standard / 4500 psi high-pressure series

Request Quote

Prices stay on the RFQ. Send size, material, quantity and destination — the factory replies with price, lead time and packing. Packing, payment and the usual quote questions are on thedelivery pageand the FAQ.

Request a factory quote

Questions about this part

How should the tube be cut before assembly?

Square and burr free. A cut that is out of square or has a raised burr lets the ferrule bite unevenly and is a common cause of a joint that weeps on first pressure.

How far should the tube go into the elbow?

Push it in until it meets the shoulder in the body, then pull up the nut. A tube stopped short of the shoulder leaves the ferrule biting air instead of tube.

Should the nut be torqued or turned?

Run the nut up finger tight, then pull it up until the ferrule grips the tube and the nut goes hard. Stop there; friction varies, so turns are more repeatable than a torque figure.

Can the joint be remade without new ferrules?

The ferrule is swaged onto the tube at first assembly and cannot be reused on a fresh tube. Remake on the same tube is possible; a new tube needs a new ferrule.

Where is the leak, the tube joint or the threaded end?

Dry the fitting and watch where the bead forms. Moisture at the nut and ferrule points to the tube joint; moisture at the body to port face means the thread or washer is at fault.

Does the pressure rating hold at temperature or with thin wall tube?

No. The 1000 psi standard series and 4500 psi high-pressure series are ratings for the fitting body. Tube wall and working temperature set what the assembly actually holds, so both must be checked.

Related products