
Stainless Steel Compression Male/Female Tee — Sizes
Compression Male/Female Tee: stainless steel compression fittings tee with thread branch options. FerruleX RFQ. Stocked sizes ship fast. Fast stock shipping.
- Brand
- FerruleX
- Material
- SS316 / SS316L / SS304
- Tube OD
- 3–25 mm / 1/8"–1"
- Type
- Compression male/female tee
- Pressure
- 1000 psi standard / 4500 psi high-pressure
- Stock5–7 days after confirmation
- Make to order15–25 days production
- Payment / termsT/T ~30% or L/C · FOB Shanghai / Ningbo
- OEMLogo and drawings accepted · price on RFQ
Description
A tee splits a live run into two directions while the third port takes a thread rather than a tube end. One body carries the compression ends on the run and a male or female thread on the branch, so an instrument mounts without a further adaptor. FerruleX builds it in 316, 316L or 304 stainless, copper on request, for tube OD 3–25 mm / 1/8"–1"; branch threads run ZG(R), NPT, G or M, from M5 to M24. Both run ends are ferrule joints and the branch is threaded, so the line stays continuous while an instrument is fitted, swapped or blanked off. Liquid and gas service, in petrochemical, pharmaceutical, food and shipbuilding lines. Pressure splits by series: 1000 psi standard, 4500 psi maximum high-pressure.
Threaded branch, compression run. That combination is what a tap or a sensor needs when the tube itself must not be cut. Decide male or female before the blank is drawn, and fix the thread standard early: ZG(R), NPT, G or M, with branch sizes from M5 to M24. Copper bodies are available on request.
- Run ends
- Compression ferrule joints on both run ports.
- Branch
- Male or female thread in ZG(R), NPT, G or M, M5 to M24.
- Materials
- SS316, SS316L or SS304, copper on request.
- Pressure
- 1000 psi standard series, 4500 psi maximum on the high-pressure version.
Specifications
| Specification | Value |
|---|---|
| Brand | FerruleX |
| Material | SS316 / SS316L / SS304 |
| Tube OD | 3–25 mm / 1/8"–1" |
| Type | Compression male/female tee |
| Pressure | 1000 psi standard / 4500 psi high-pressure |
Request Quote
Prices stay on the RFQ. Send size, material, quantity and destination — the factory replies with price, lead time and packing. Packing, payment and the usual quote questions are on thedelivery pageand the FAQ.
Questions about this part
How should the tube be prepared before it goes into the tee?
Cut the tube square and deburr both the outside and the bore. Any burr or oval end scores the ferrule seat as the nut is drawn down, so the joint leaks from the first assembly.
How far does the tube go into the body?
Push it in until it bottoms on the shoulder inside the bore, then hold it there while the nut is made up. A tube that stops short leaves the ferrule biting on the wrong section.
Is make-up set by torque or by turns?
By feel and by turns rather than a torque figure, since the nut pulls up to a firm stop. Once the nut shoulders, stop: further turning only stretches the thread and distorts the ferrule.
Can the joint be taken apart and remade?
Yes, the joint can be remade, but inspect the ferrule first. A ferrule that has been fully swaged stays on the tube and is normally reused in the same position; a distorted one should be replaced.
The assembly leaks, so is it the tube joint or the branch thread?
Dry the part and watch where fluid reappears. Weeping at the nut points to the ferrule or the tube end; seepage at the branch points to the thread, which needs a suitable sealant or gasket.
Does the pressure rating depend on the tube wall and the temperature?
Yes. The rating belongs to the fitting body; the tube wall must support the same pressure, and both fall as the temperature rises. Service conditions are confirmed at order.
Related products

Stainless Steel Compression Reducing Tee — Sizes
Compression Reducing Tee: stainless steel compression fittings with smaller branch take-off. FerruleX factory RFQ. Stocked sizes ship fast. Fast stock shipping.
View details →
Stainless Steel Cylinder Connector — Sizes & Specs
Cylinder Connector: compact stainless instrumentation fitting for cylinder and specialty ports. SS316/304. FerruleX RFQ. Stocked sizes ship fast.
View details →
Stainless Steel Compression Bulkhead Union — Sizes
Compression Bulkhead Union: panel-pass stainless steel compression fittings, double ferrule. SS316/304. FerruleX RFQ. Stocked sizes ship fast. OEM RFQ welcome.
View details →
Compression Cross Fitting
Compression Cross Fitting: four-port stainless steel compression fittings for intersecting lines. FerruleX RFQ. Stocked sizes ship fast. Fast stock shipping.
View details →