
Compression Cross Fitting
Compression Cross Fitting: four-port stainless steel compression fittings for intersecting lines. FerruleX RFQ. Stocked sizes ship fast. Fast stock shipping.
- Brand
- FerruleX
- Material
- SS316 / SS316L / SS304
- Tube OD
- 3–25 mm / 1/8"–1", equal or reducing
- Type
- Cross, four-way, tube ends
- Pressure
- 1000 psi standard / 4500 psi high-pressure
- Stock5–7 days after confirmation
- Make to order15–25 days production
- Payment / termsT/T ~30% or L/C · FOB Shanghai / Ningbo
- OEMLogo and drawings accepted · price on RFQ
Description
A cross puts four compression ends on one body, joining four tube lines at a single point instead of stacking two tees. Four connections also mean four places a joint can weep, so each ferrule is made up on its own: hold the body steady and tighten one nut at a time to the maker procedure, rather than using the body as a wrench to pull a nut down. Every end is a two-ferrule bite joint — body, ferrule, nut — with no weld and no thread sealant on the tube side. Ends take 3–25 mm and 1/8"–1" tube in 316, 316L or 304; threaded ends in M5–M24 or NPT, G or R (BSPT) are available where a port replaces a tube leg. If the four lines arrive stressed, align or support the tubing — tightening order will not take the stress out.
Four-way compression cross with tube ends, 3–25 mm and 1/8–1 in; threaded ends M5–M24 or NPT / G / R (BSPT) available. Hold the body steady and make up each ferrule on its own. 316 / 316L / 304 stainless, standard series to 1000 psi, 4500 psi high-pressure.
- One at a time
- Hold the body steady; make up each ferrule to the maker procedure.
- Leak points
- Four joints on one body; check every ferrule bite before pressurising.
- End options
- Tube ends 3–25 mm and 1/8"–1"; a leg can be threaded M5–M24.
- Support
- Align or clamp the tubing; tightening order does not remove stress.
Specifications
| Specification | Value |
|---|---|
| Brand | FerruleX |
| Material | SS316 / SS316L / SS304 |
| Tube OD | 3–25 mm / 1/8"–1" |
| Type | Cross, four-way |
| Threaded leg | M5–M24 / NPT / G / R (BSPT) on request |
| Pressure | 1000 psi standard / 4500 psi high-pressure series |
Request Quote
Prices stay on the RFQ. Send size, material, quantity and destination — the factory replies with price, lead time and packing. Packing, payment and the usual quote questions are on thedelivery pageand the FAQ.
Questions about this part
How deep does the tube go into each port?
Push the tube in until it bottoms on the internal shoulder, then mark that depth. Make up the ferrule from that seated position; a tube short of the shoulder cannot be sealed by tightening.
Should I tighten by torque or by counting turns?
Follow the maker procedure for the series you bought, which sets make-up by turns from finger-tight. Torque figures only hold when the thread is clean and lightly lubricated, so turns are the safer check on site.
A port weeps right after assembly. Tube end or threaded leg?
Dry the body and watch where the bead forms. A weep at the nut means the ferrule bite is incomplete or the tube was short of the shoulder; a weep at a threaded leg means the port seal needs remaking.
Can I remake a joint with the same ferrules?
A single remake to the same procedure is normally accepted, but the ferrule has already been deformed once. If the joint has been apart more than that, fit a new ferrule and nut rather than chasing the old bite.
Can I mix ferrules from different makers in one port?
No. Ferrules and nuts are matched to the body cone and thread by their maker, so a mixed set can seat at the wrong depth. Keep one maker per joint; a cross has four joints to keep consistent.
Does the cross need support against vibration?
Yes. Clamp the tubing close to the body on each run, because a cross carries four lines and the body takes the load of all of them. Support stops flexing at the ferrule bite.
Related products

Ground Finish Tube to Male Connector
Ground Finish Tube to Male Connector: refined stainless steel compression fittings, tube to male. FerruleX RFQ. Stocked sizes ship fast. Fast stock shipping.
View details →
Ground Finish Reducing Union
Ground Finish Reducing Union: polished-look stainless steel compression fittings, unequal OD. FerruleX RFQ. Stocked sizes ship fast. Export RFQ only — no cart.
View details →
Ground Finish Straight Union
Ground Finish Straight Union: equal tube stainless steel compression fittings with ground exterior. FerruleX RFQ. Stocked sizes ship fast. Fast stock shipping.
View details →
Stainless Steel Ground Finish Male Elbow — Sizes
Ground Finish Male Elbow: 90° ground stainless steel compression fittings, tube to male. FerruleX RFQ. Stocked sizes ship fast. Export RFQ only — no cart.
View details →