Skip to content

Need stainless steel fittings, valves or hose?

Ground Finish Reducing Union — FerruleX stainless steel fittings

Ground Finish Reducing Union

Ground Finish Reducing Union: polished-look stainless steel compression fittings, unequal OD. FerruleX RFQ. Stocked sizes ship fast. Export RFQ only — no cart.

Brand
FerruleX
Material
SS316 / SS316L / SS304
Size range
OD 3–25 mm / 1/8"–1"
Finish
Ground
Type
Reducing union

Request a factory quote

  • Stock5–7 days after confirmation
  • Make to order15–25 days production
  • Payment / termsT/T ~30% or L/C · FOB Shanghai / Ningbo
  • OEMLogo and drawings accepted · price on RFQ

Description

A reducing union absorbs a step in the line: one port is machined for a smaller tube OD than the other, so a run can drop size at a single joint instead of using an adapter. On the ground grade the body is surfaced after machining, so the OD carries no turning marks. Ports span 3 mm to 25 mm and 1/8 in to 1 in (3.175 mm to 25.4 mm), in 316, 316L or 304 stainless. Ferrule ends, bright tube or hard tube, liquid and gas service. Standard build sits near 1000 psi, the high-pressure build reaches about 4500 psi. Send the two tube ODs separately, with the finish callout, on the RFQ.

Finish is named on the drawing, so treat it as a line item, not a note. The two ports take unequal tube ODs; both numbers go on the order. Grinding follows machining and touches the body OD alone. A ground face holds handling marks, so wipe parts before packing. Above 230 °C (450 °F), specify the high-temperature build.

Reduction
One port is machined to a smaller tube OD than the other.
Surface
Body OD is ground after machining, removing the turning marks.
Pressure
Near 1000 psi as standard, about 4500 psi in the high-pressure build.
Ordering
Both tube ODs and the finish callout belong on the RFQ.

Specifications

SpecificationValue
BrandFerruleX
MaterialSS316 / SS316L / SS304
Size rangeOD 3–25 mm / 1/8"–1"
FinishGround
TypeReducing union

Request Quote

Prices stay on the RFQ. Send size, material, quantity and destination — the factory replies with price, lead time and packing. Packing, payment and the usual quote questions are on thedelivery pageand the FAQ.

Request a factory quote

Questions about this part

How should the tube ends be cut before either port is made up?

Square cut with a fine saw, then deburr both inside and outside. A burr or an angled cut lets the ferrule bite unevenly, and the smaller port of a reducing body has less room to absorb that.

How far does each tube go into the body?

Push the tube to the shoulder in the port, not merely past the ferrule. Seat the larger and the smaller line separately, because the two ports differ in bore and depth.

Are the nuts set by torque or by turn count?

Turn count from finger tight, taken up in steps rather than one sweep. A torque wrench serves as a final check against the figure your own procedure quotes for the size.

Can ferrules from another maker be fitted to this body?

No. Body, ferrule and nut are matched as one set. A ferrule from another maker carries its own seat geometry, will not bed correctly, and the set should be replaced as a unit.

The joint weeps straight after make-up. Should we tighten it further?

Take it apart first. Tightening past the set point drives the ferrule into the tube and damages the seat; a leak at make-up usually means the tube sat short of the shoulder.

What holds the smaller line steady when the run vibrates?

Support both legs close to the union and give each one a straight length before any bend. Vibration works the nut loose on the smaller port first, since it carries less tube stiffness.

Related products