Skip to content

Need stainless steel fittings, valves or hose?

Ground Finish Male Elbow — FerruleX stainless steel fittings

Stainless Steel Ground Finish Male Elbow — Sizes

Ground Finish Male Elbow: 90° ground stainless steel compression fittings, tube to male. FerruleX RFQ. Stocked sizes ship fast. Export RFQ only — no cart.

Brand
FerruleX
Material
SS316 / SS316L / SS304
Tube OD
3–25 mm / 1/8"–1"
Finish
Ground
Pattern
Male elbow

Request a factory quote

  • Stock5–7 days after confirmation
  • Make to order15–25 days production
  • Payment / termsT/T ~30% or L/C · FOB Shanghai / Ningbo
  • OEMLogo and drawings accepted · price on RFQ

Description

A tube run that has to finish square to a panel turns here, then leaves through a threaded male end. Body stock is 316, 316L or 304 stainless, with copper available on request, and the exterior is dressed after machining. Tube ends cover 3 mm to 25 mm, that is 1/8 in to 1 in. Male threads are cut ZG(R), NPT, G or M. Standard bodies work to about 1000 psi, the high-pressure variant to roughly 4500 psi, on liquid or gas. Three lines on the order settle the part: tube OD, male thread, ground finish. Leave swing room for the branch nut before the male end is torqued home.

Grinding is an exterior operation, run for appearance and for cleaning in visible cabinets. It stops at the body surface, so the ferrule path is untouched and the joint behaves as the same elbow in a plain finish. State the finish beside the tube OD and male thread when one skid carries both ground and unground parts.

Bend
90° turn from the tube end to the male port.
Materials
316, 316L or 304 stainless, with copper on request.
Threads
ZG(R), NPT, G or M on the male end.
Pressure
About 1000 psi standard, roughly 4500 psi on the high-pressure variant.

Specifications

SpecificationValue
BrandFerruleX
MaterialSS316 / SS316L / SS304
Tube OD3–25 mm / 1/8"–1"
FinishGround
PatternMale elbow

Request Quote

Prices stay on the RFQ. Send size, material, quantity and destination — the factory replies with price, lead time and packing. Packing, payment and the usual quote questions are on thedelivery pageand the FAQ.

Request a factory quote

Questions about this part

How should the tube be prepared before it goes into the elbow?

Cut the tube square and deburr both the outside edge and the bore before insertion. A burr or an out-of-square cut lifts the ferrule off the tube and the joint will leak no matter how hard the nut is turned.

How far does the tube go into the male elbow body?

Push the tube in until it seats against the shoulder inside the body, then mark the tube at the nut so the depth can be checked again. The ferrule grips at that seated position, not short of it.

Should the nut be tightened by torque or by counting turns?

Tighten to the maker specified torque rather than counting turns, because turns alone do not account for tube wall or lubricant. Bring the nut down evenly and let the ferrule bite without the body turning in the port.

Can a joint that has been taken apart be remade?

A joint already made can be remade, but fit a new ferrule each time. The old ferrule is already swaged onto the tube and will not seal again at the same point.

Can parts from different makers be mixed on one elbow?

Keep body, ferrule and nut from the same maker. Threads and ferrule angles vary between brands, and a mixed set may pull up short of the seat, so it leaks at the tube joint.

The joint leaks after assembly. Is it the tube end or the threaded end?

Wipe the joint dry and watch where the fluid returns. A weep at the nut points to the ferrule or the tube end; a weep at the male thread points to the port thread or its sealing face.

Related products