Skip to content

Need stainless steel fittings, valves or hose?

Forged Compression Tee — FerruleX stainless steel fittings

Stainless Steel Forged Compression Tee — Types

Forged Compression Tee: forged stainless steel compression fittings for three-port branching. FerruleX RFQ. Stocked sizes ship fast. Export RFQ only — no cart.

Brand
FerruleX
Material
SS316 / SS316L / SS304
Tube OD
3–25 mm / 1/8"–1"
Body
Forged
Type
Compression tee

Request a factory quote

  • Stock5–7 days after confirmation
  • Make to order15–25 days production
  • Payment / termsT/T ~30% or L/C · FOB Shanghai / Ningbo
  • OEMLogo and drawings accepted · price on RFQ

Description

Tube outside diameter runs from 3 mm to 25 mm, and from 1/8 in to 1 in (3.175 mm to 25.4 mm), on a die-forged stainless body with three ferrule ports. Standard material is 316, 316L or 304 stainless; copper is available on request. The joint is ferrule compression for bright tube or hard tube, in liquid or gas service. Equal and reducing versions are made as separate items; the reducing version carries a smaller branch OD. Standard bodies work around 1000 PSI, and the high-pressure version reaches roughly 4500 PSI. Petrochemical, shipbuilding, food processing and pharmaceutical lines are the usual applications. Run OD and branch OD belong on separate RFQ lines.

One die-forged body carries the run and the branch, with ferrule joints for bright or hard tube. Standard pressure sits near 1000 PSI, and a high-pressure build reaches about 4500 PSI. Equal and reducing versions share the same 3 mm to 25 mm OD range, so a branch size change does not force a second tee family.

Forging
Die-forged body in 316, 316L or 304 stainless, with copper available on request.
Ports
Three ferrule joints sized for 3 mm to 25 mm tube outside diameter.
Pressure
Standard bodies hold around 1000 PSI; the high-pressure build reaches about 4500 PSI.
Branch
Equal and reducing bodies are separate items, so the branch OD is quoted on its own.

Specifications

SpecificationValue
BrandFerruleX
MaterialSS316 / SS316L / SS304
Tube OD3–25 mm / 1/8"–1"
BodyForged
TypeCompression tee

Request Quote

Prices stay on the RFQ. Send size, material, quantity and destination — the factory replies with price, lead time and packing. Packing, payment and the usual quote questions are on thedelivery pageand the FAQ.

Request a factory quote

Questions about this part

How much tube preparation does the ferrule joint need?

Cut the tube square and deburr both the outside and the bore before insertion; a burr or an out-of-square cut lets the ferrule bite unevenly and is a common cause of a weeping joint.

How far does the tube go into each port?

Push the tube into each of the three ports until it bottoms on the shoulder; do not stop short, because the ferrule position is set by that shoulder and the branch port is checked the same way.

How far do I tighten a new ferrule nut?

Tighten a new ferrule by the specified number of turns after finger-tight, not by feel; the tee has three joints, so hold the body and tighten each nut in turn rather than using one port as a reaction point.

Can the same ferrule be reused when a joint is remade?

Once a ferrule has been crimped it stays with that tube. To remake the joint, cut the tube back and fit a fresh ferrule and nut rather than reusing the old set on a new position.

The joint weeps right after assembly. Where do I look first?

A leak straight after assembly is usually one joint, not the body. Pressurise and check each of the three ports in turn, and separate a weeping tube joint from a leaking threaded connection before tightening anything.

Is the pressure rating valid for any tube wall and temperature?

The stated pressure applies only with tube of matching wall and at the rated temperature. A thin wall tube or a hot line lowers what the joint holds, so rate the tee from the weakest of body, tube and ferrule.

Related products