Skip to content

Need stainless steel fittings, valves or hose?

Compression Tube to Male Connector — FerruleX stainless steel fittings

Compression Tube to Male Connector

Compression Tube to Male Connector: stainless steel compression fittings, double ferrule, SS316/304, NPT/G. FerruleX RFQ. Stocked sizes ship fast.

Brand
FerruleX
Material
SS316 / SS316L / SS304
Tube OD
3–25 mm / 1/8"–1"
Threads
M5–M24 / NPT / G / R (BSPT)
Pressure
1000 psi standard / 4500 psi high-pressure

Request a factory quote

  • Stock5–7 days after confirmation
  • Make to order15–25 days production
  • Payment / termsT/T ~30% or L/C · FOB Shanghai / Ningbo
  • OEMLogo and drawings accepted · price on RFQ

Description

The tube-to-male connector is where a compression run meets a tapped port: tube on one end, male thread on the other. The tube end is a two-ferrule bite joint — no weld, no thread sealant on the tube side. The specification risk here is not the tube, it is the thread: M5–M24 metric and NPT, G or R (BSPT) pipe threads are not interchangeable, and a letter size alone does not define the form. Name the standard and the size on the RFQ — 1/4 NPT, not 1/4 thread. Tube sizes run 3–25 mm and 1/8"–1" in 316, 316L or 304, for liquid or gas. Gauge blocks, manifold outlets and analyzer panels use this pattern because make-up needs no welding.

Straight connector with a compression tube end and a male thread end, M5–M24 or NPT / G / R (BSPT), tube 3–25 mm and 1/8–1 in. Name the thread standard on the RFQ. 316 / 316L / 304 stainless, standard series to 1000 psi and 4500 psi high-pressure.

Thread first
NPT, G and R (BSPT) are not interchangeable; name the standard and the size.
Port match
Check the tapped port is M5–M24 metric or NPT / G / R, not just a letter size.
Tube side
Fully annealed tube, below HRB 90 / HV 190, bottomed with 10 mm straight past the nut.
Make-up
Compression on one end, thread on the other: no welding on the tube side.

Specifications

SpecificationValue
BrandFerruleX
MaterialSS316 / SS316L / SS304
Tube OD3–25 mm / 1/8"–1"
ThreadsM5–M24 metric, NPT, G, R (BSPT)
TypeStraight, tube to male thread
Pressure1000 psi standard / 4500 psi high-pressure series

Request Quote

Prices stay on the RFQ. Send size, material, quantity and destination — the factory replies with price, lead time and packing. Packing, payment and the usual quote questions are on thedelivery pageand the FAQ.

Request a factory quote

Questions about this part

How should the tube be prepared before assembly?

Cut the tube square and deburr both the outside and the bore. A burr or an out-of-square cut lets the front ferrule ride off the tube axis, and the joint will not seal.

How far does the tube go into the connector?

Insert the tube until it seats on the internal shoulder of the body, keep it pressed in, and run the nut down by hand. Do not judge insertion depth by eye or by a mark.

How tight should the nut be?

Run the nut up finger tight, then tighten with a wrench while a second wrench holds the body. Never tighten on the tube alone, or the tube will twist and the bite will be lost.

Can a joint be remade with the same ferrules?

Only if the bite is clean and the tube surface is unmarked. If a ferrule has been over-tightened or the tube is scored, fit new ferrules rather than reusing the old set.

The joint leaks — is it the tube end or the thread end?

A leak at the tube end points to an incomplete bite, a scored tube or a ferrule that was not seated. A leak at the threaded end is a port thread mismatch or short make-up.

Does the pressure rating depend on the tube and the temperature?

The rating applies only with a tube of sufficient wall thickness, and it falls as the working temperature rises. Check both before choosing the standard or the high-pressure series.

Related products