Skip to content

Need stainless steel fittings, valves or hose?

Ground Finish Straight Union — FerruleX stainless steel fittings

Ground Finish Straight Union

Ground Finish Straight Union: equal tube stainless steel compression fittings with ground exterior. FerruleX RFQ. Stocked sizes ship fast. Fast stock shipping.

Brand
FerruleX
Material
SS316 / SS316L / SS304
Tube OD
3–25 mm / 1/8"–1"
Finish
Ground
Type
Straight union

Request a factory quote

  • Stock5–7 days after confirmation
  • Make to order15–25 days production
  • Payment / termsT/T ~30% or L/C · FOB Shanghai / Ningbo
  • OEMLogo and drawings accepted · price on RFQ

Description

Straight union for equal tube ends, body exterior ground rather than left as-machined. A ferrule sits at each end, so the flow path carries no thread. Sizes run Φ3 mm to Φ25 mm, which covers Φ1/8 in to Φ1 in (3.175 mm to 25.4 mm). Bodies are 316, 316L or 304 stainless. The joint is a ferrule type and is normally used with bright tube or hard tube. Service media are liquid and gas. Standard bodies are rated around 1000 psi; the high-pressure variant reaches about 4500 psi. Order by tube OD and put the finish note on the RFQ.

Only the outside is reworked. The ground union takes the same tube OD, ferrule set and nut as the as-machined body, so a drawing change is a finish note, not a new line item. Ferrule connection at both ends, for bright tube or hard tube; liquid and gas service. Common sizes are held in stock.

Form
Equal straight union, tube end to tube end.
Range
Φ3 mm to Φ25 mm, covering Φ1/8 in to Φ1 in (3.175 mm to 25.4 mm).
Material
316, 316L or 304 stainless.
Pressure
Standard bodies around 1000 psi, high-pressure variant to about 4500 psi.

Specifications

SpecificationValue
BrandFerruleX
MaterialSS316 / SS316L / SS304
Tube OD3–25 mm / 1/8"–1"
FinishGround
TypeStraight union

Request Quote

Prices stay on the RFQ. Send size, material, quantity and destination — the factory replies with price, lead time and packing. Packing, payment and the usual quote questions are on thedelivery pageand the FAQ.

Request a factory quote

Questions about this part

How square does the tube cut need to be before assembly?

Cut the tube square and deburr both the outside edge and the bore before insertion. A burr or an angled cut lets the ferrule bite off centre, and the joint will leak however far the nut is turned.

How far should the tube go into the union body?

Push the tube in until it seats against the shoulder inside the body, then hold it there while the nut is turned. Marking the insertion depth on the tube makes the second end easier to check.

Should I tighten by torque or by counting turns?

Turn the nut by hand until it is finger tight, then finish with a wrench to the point where the ferrule grips. Turns alone are unreliable across sizes, so a torque wrench is the better control on repeat work.

Can a made up joint be taken apart and remade?

Yes, if the ferrule and tube are undamaged. Loosen the nut, withdraw the tube, then remake to the same depth and tighten to the original position. Fit a new ferrule if the old one has been crushed or scored.

Can I mix the body, ferrule and nut from different makers?

Keep the body, ferrule and nut as one maker set. Ferrules are ground to their own body seat, and a mixed set may grip on a different angle, so the joint can leak or the tube can be cut through.

How do I tell which end of the union is leaking?

Wipe the body dry and watch each end under pressure. A leak at either ferrule means the tube cut, insertion depth or nut position is at fault, not the body itself, which carries no thread in the flow path.

Related products