Skip to content

Need stainless steel fittings, valves or hose?

Ground Finish Tube to Male Connector — FerruleX stainless steel fittings

Ground Finish Tube to Male Connector

Ground Finish Tube to Male Connector: refined stainless steel compression fittings, tube to male. FerruleX RFQ. Stocked sizes ship fast. Fast stock shipping.

Brand
FerruleX
Material
SS316 / SS316L / SS304
Tube OD
3–25 mm / 1/8"–1"
Finish
Ground
Threads
NPT / G / Metric

Request a factory quote

  • Stock5–7 days after confirmation
  • Make to order15–25 days production
  • Payment / termsT/T ~30% or L/C · FOB Shanghai / Ningbo
  • OEMLogo and drawings accepted · price on RFQ

Description

Finish gets specified separately from the joint. A tube-to-male body is machined, then its outside is ground to remove turning marks from the flats, the hex and the barrel; the ferrule bore and the male thread are cut to the same dimensions as the standard connector. That matters when the fitting is left exposed on a skid or on an instrument panel. Tube side takes Φ3 mm to Φ25 mm or 1/8 in to 1 in, port side M5 to M24 in ZG(R), NPT, G or M. Bodies in 316, 316L, 304 stainless or copper, for liquid and gas. Roughly 1000 PSI on the standard pattern, up to about 4500 PSI on the high-pressure pattern.

Grinding is a surface operation, not a functional one: it removes turning marks and leaves a clean exterior for wipedown, without altering ferrule grip, thread engagement or pressure pattern. Order it when the fitting is on show or washed down regularly; take the turned body inside a cabinet. Thread standard and port size are specified apart from tube OD.

Finish
Outside ground after machining to strip turning marks from flats, hex and barrel.
Pressure
Standard body about 1000 PSI, high-pressure body up to about 4500 PSI.
Sizes
Tube Φ3 mm to Φ25 mm or 1/8 in to 1 in, port thread M5 to M24.
Threads
Male end cut ZG(R), NPT, G or M, chosen against the tapped port.

Specifications

SpecificationValue
BrandFerruleX
MaterialSS316 / SS316L / SS304
Tube OD3–25 mm / 1/8"–1"
FinishGround
ThreadsNPT / G / Metric

Request Quote

Prices stay on the RFQ. Send size, material, quantity and destination — the factory replies with price, lead time and packing. Packing, payment and the usual quote questions are on thedelivery pageand the FAQ.

Request a factory quote

Questions about this part

How should the tube end be prepared before the ferrule grips it?

Cut square with a tube cutter and deburr inside and out. Burrs and a slanted cut stop the ferrule seating evenly, so the joint leaks at the tube side no matter how far the nut is turned.

How deep should the tube go into the body?

Push the tube fully home against the shoulder in the body before the nut is run up. If it stops short, the ferrules grip too far out and the joint will not hold pressure.

Is the nut set by torque figure or by turns?

Snug the nut by hand until it contacts the ferrule, then set it by counting turns rather than reading a torque wrench. Friction on small tube sizes varies too much for a torque figure to be reliable.

Can the joint be remade with the same ferrules?

Yes, once. A remade joint reuses the ferrules that are already swaged and only needs the nut brought back to its set position. Fit new ferrules when the tube is replaced or the old ones are scored.

Where is the leak, at the tube joint or at the male thread?

Wipe the joint dry and watch both ends under pressure. A weep at the tube side means the ferrules are not seated; a weep at the male thread means the port thread or the sealing face needs attention.

Does the pressure rating change with tube wall or temperature?

It does. The figure on this page is for the body pattern only: about 1000 PSI standard and about 4500 PSI high pressure. A thin wall tube or a hot service lowers what the assembly holds.

Related products