
Compression Union Elbow
Compression Union Elbow: 90° stainless steel compression fittings, tube-to-tube double ferrule. FerruleX RFQ. Stocked sizes ship fast. Fast stock shipping.
- Brand
- FerruleX
- Material
- SS316 / SS316L / SS304
- Tube OD
- 3–25 mm / 1/8"–1"
- Type
- Union elbow, tube to tube, 90°
- Pressure
- 1000 psi standard / 4500 psi high-pressure
- Stock5–7 days after confirmation
- Make to order15–25 days production
- Payment / termsT/T ~30% or L/C · FOB Shanghai / Ningbo
- OEMLogo and drawings accepted · price on RFQ
Description
A panel run rarely stays straight for long. The union elbow takes the 90° turn without a bender, a weld or a swivel adaptor: tube in, tube out, at right angles. Both ends are two-ferrule bite joints — body, ferrule, nut — so nothing on the tube side is welded or sealed with compound, and the joint stays demountable for later instrument swaps. Ends take 3–25 mm and 1/8"–1" tube in 316, 316L or 304, for liquid or gas, at 1000 psi standard series or 4500 psi on the high-pressure series. One rule matters more at a corner than anywhere else: the tube must bottom in the body, and each nut needs at least 10 mm of straight tube behind it. On a 90° fitting that run-up has to be planned on both legs, because a bend cannot start at the nut.
Tube-to-tube 90° union elbow in 316, 316L or 304 stainless, 3–25 mm and 1/8–1 in. Two-ferrule bite joint, no weld, demountable. Standard series to 1000 psi, 4500 psi high-pressure. Allow 10 mm of straight tube past each nut on both legs of the corner.
- Corner runs
- Turns a panel run 90° without a bender or a welded bend.
- Straight length
- 10 mm of straight tube behind each nut, planned on both legs.
- Demountable
- Two-ferrule bite joint; the line opens again for instrument swaps.
- Pressure
- 1000 psi standard series, 4500 psi high-pressure series.
Specifications
| Specification | Value |
|---|---|
| Brand | FerruleX |
| Material | SS316 / SS316L / SS304 |
| Tube OD | 3–25 mm / 1/8"–1" |
| Type | Union elbow, 90°, tube to tube |
| Pressure | 1000 psi standard / 4500 psi high-pressure series |
| Tube standard | ASTM A269 / GB/T 14976, fully annealed |
Request Quote
Prices stay on the RFQ. Send size, material, quantity and destination — the factory replies with price, lead time and packing. Packing, payment and the usual quote questions are on thedelivery pageand the FAQ.
Questions about this part
How should the tube ends be prepared before assembly?
Cut square with a tube cutter and deburr both the outside edge and the bore. A raised burr stops the tube seating on the shoulder and scores the ferrule as the nut is driven home.
How far does the tube go into the elbow body?
Push it in until it bottoms against the internal shoulder, then hold it there while the nut is tightened. If it does not reach the shoulder, the ferrules bite short and the joint leaks.
Do I tighten the nut to a torque figure or by turns?
By turns on the nut, watching the ferrule bite rather than a torque wrench. Torque figures scatter with thread lubrication and tube hardness, so the turn count is the repeatable reference on this fitting.
Can a joint be remade with the same ferrules?
The front ferrule stays on the tube and can be remade a few times, but fresh ferrules are the safer choice. Inspect the bite for a cracked or distorted edge before reusing it.
Does the 1000 psi rating hold for any tube wall?
No. The rating belongs to the fitting and a matching heavy-wall tube, and falls once the wall thins or the temperature rises. Thin-wall tube at the corner is where a joint is most likely to fail.
What does vibration do to the corner joint?
It works the nut loose and fatigues the tube just past the bite. Support the tube close to each nut on both legs, and check the nuts after the first weeks of a pump-driven line.
Related products

Stainless Steel Compression Male/Female Tee — Sizes
Compression Male/Female Tee: stainless steel compression fittings tee with thread branch options. FerruleX RFQ. Stocked sizes ship fast. Fast stock shipping.
View details →
Stainless Steel Compression Reducing Tee — Sizes
Compression Reducing Tee: stainless steel compression fittings with smaller branch take-off. FerruleX factory RFQ. Stocked sizes ship fast. Fast stock shipping.
View details →
Stainless Steel Cylinder Connector — Sizes & Specs
Cylinder Connector: compact stainless instrumentation fitting for cylinder and specialty ports. SS316/304. FerruleX RFQ. Stocked sizes ship fast.
View details →
Stainless Steel Compression Bulkhead Union — Sizes
Compression Bulkhead Union: panel-pass stainless steel compression fittings, double ferrule. SS316/304. FerruleX RFQ. Stocked sizes ship fast. OEM RFQ welcome.
View details →