Skip to content

Need stainless steel fittings, valves or hose?

What Is a Compression Fitting? Types & How It Works

What a stainless steel compression fitting is, how double-ferrule seals work, and when FerruleX factory buyers should choose compression over weld or thread.

Sep 14, 2026 · 5 min read · FerruleX Factory

Stainless steel compression fittings on instrumentation tubing

A compression fitting joins metal tubing to a port or to another tube without welding, threading the tube, or any hot work at all.

It is a body with a conical seat, one or two ferrules and a nut. Tightening the nut drives the ferrules onto the tube OD until they bite and seal metal-to-metal. The joint is remakeable in the field, needs no heat and takes no thread sealant.

Key takeaways

  • A compression fitting seals by mechanical bite: tightening the nut drives one or two ferrules onto the tube OD, forming a metal-to-metal seal and grip in the same assembly — no welding, no thread sealant, no heat.
  • Compression fittings are sized by tube outside diameter, not pipe size: fractional 1/16” to 2” and metric 2 mm to 50 mm cover the practical range.
  • Choose compression when the joint must be assembled and remade in the field; choose threaded adapters for pipe ports and weld ends only where the joint will never need to come apart.

Which joint do I need — compression, thread or weld?

Compression suits tube. Threaded joints suit pipe. Weld suits permanence. Most skids use all three, and the skill is putting each where its mechanism belongs.

What you are joining Choice What decides it Note
Instrument tube run opened again in field Compression, double ferrule Whether the joint must be assembled and remade on site No hot work, remakeable, tolerates vibration
Connection into an existing pipe thread port Threaded adapters or valves Whether the port already carries the thread Seals on tape or sealant, not on a bite
Permanent process joint Weld ends Whether the joint will ever need to come apart No mechanical joint at all, highest purity
Soft tubing that cannot take a bite Compression with insert Whether the tube ID needs support against collapse The insert holds the tube wall against the ferrule

Compression earns its place on analyzer and sample lines, gauge and instrument manifolds, pneumatic and hydraulic control tubing, food and beverage process instrumentation, and marine and offshore panels — anywhere a clean tube run needs remakeable joints without a welder on site.

It is not the answer for everything: slurries and solids plug the fine seal geometry, and very high-pressure severe service belongs to cone-and-thread or welded systems.

What is inside a compression joint?

Every compression joint, whatever the brand or pattern, has the same working cast: a body with a conical seat, one or two ferrules (metal rings), and a threaded nut.

The ferrules do all the sealing and gripping; the nut and body only supply the force. Because the seal is mechanical, it tolerates vibration and remaking better than any dope-and-thread joint — provided the tube is within the maker’s hardness range and the ferrules are assembled in the right order.

Single or double ferrule — which pattern?

Two patterns divide the family. A single-ferrule fitting makes one ring do both jobs — seal and grip — and suits stationary lines inside its rated pressures. A double-ferrule fitting splits the work: the front ferrule forms the primary seal, while the back ferrule grips against pull-out and absorbs vibration.

Pattern What seals What grips What decides it
Single ferrule One ring does seal and grip The same ring Stationary lines inside rated pressure, joint rarely opened
Double ferrule Front ferrule forms primary seal Back ferrule grips against pull-out and absorbs vibration Instrumentation, gas service, anywhere joints are remade

The double pattern is the default on instrumentation, gas service and anywhere joints are remade. The full comparison of patterns, pressure classes and selection rules lives in single ferrule vs double ferrule — the short version: vibration and remaking push you to double.

What size do I order?

Compression fittings are sized by tube outside diameter — never by pipe size and never by the thread on the port end. Fractional sizes run 1/16” to 2”; metric runs 2 mm to 50 mm. A “6 mm compression fitting” expects 6.0 mm tube; a “1/4 inch” expects 6.35 mm. They are close but not interchangeable, and ordering the wrong system is a classic cross-border mistake.

Check the tube marking before the RFQ, not after the leak test. Then put this on the RFQ:

  • Tube OD, for both ends if they differ
  • Thread on the port end
  • Material
  • Quantity
  • Tube hardness, and whether the tube is soft annealed
  • Metric or fractional system, confirmed against the tube marking

Soft annealed tube seals more reliably on gas service. If you are unsure about tube hardness, say so and we flag it before quoting — see how to install compression fittings for what happens at assembly, then browse the compression category or request a quote.

How do I make up the joint?

The procedure is the same on any pattern. The order is what matters.

  1. Cut and deburr. Cut the tube square, deburr it, and slide it through the nut and the ferrules.
  2. Seat the tube. Push the tube end until it rests against the shoulder of the body.
  3. Check the stack. Confirm the ferrules are assembled in the right order for the pattern.
  4. Tighten the nut. The nut drives the ferrules forward into the body’s cone.
  5. Read the result. The cone swages the ferrules into the tube surface while pressing a seal against the body seat — bite and seal in one movement.

What goes wrong, and what do I change?

Symptom Most likely cause What to change
Joint seeps at first makeup Sealant or tape on the tube lubricated the bite, so the nut is under-tightened Assemble clean and dry, then tighten to the maker’s prescription
Leak returns soon after a remake Permanently deformed ferrules reused Cut a fresh tube section and fit new ferrules
Tube pulls out under pressure or vibration Single ferrule carrying a line that gets remade or shaken Move the joint to the double-ferrule pattern
Tube wall collapses, bite sits uneven Tube too soft for the bite, or the tube ID is unsupported Fit an insert and state tube hardness on the RFQ
Flow drops, fine seal plugs Slurry or solids in the line Compression is the wrong joint for this service
Ferrule lands in the wrong place, tube bottoms short Tube not cut square and deburred, or ferrules out of order Recut square, deburr, assemble in the maker’s order
1/4” tube will not enter a “6 mm” fitting Metric and fractional systems mixed Read the tube marking before the RFQ

FAQ

Is a compression fitting the same as a ferrule fitting? Almost — “ferrule fitting” names the family after its sealing element, and catalogs use both terms for the same joints. The ferrule-level detail — bite mechanics, hardness rules, remake limits — is covered in what is a ferrule fitting.

Can compression fittings be reused? The body and nut survive many remakes; the ferrules do not. They deform permanently on first makeup and must be replaced whenever the joint is opened. Remake on a freshly cut tube section and the joint performs like new.

Do compression fittings need sealant or tape? No. The seal is metal-to-metal between the ferrule and the body seat. Sealant on the tube can lubricate the bite and cause under-tightening — assemble clean and dry, then tighten to the maker’s prescription.

What is the difference between tube OD and pipe size? Pipe size (NPS) is a nominal bore with a fixed OD per schedule; tube size is the actual outside diameter. A 1/2” compression fitting takes 1/2” tube. Its bore has nothing to do with pipe schedules.

Can I mix tube sizes in one fitting? Yes — reducing unions and connectors join different tube ODs in one body, and adapters step from tube OD to pipe thread on the port side. List both sizes explicitly on the RFQ so the factory quotes the right body.

Related: flare vs compression fittings.

Related articles

More guides for stainless steel fittings buyers.