Skip to content

Need stainless steel fittings, valves or hose?

Angle Compression Ball Valve — FerruleX stainless steel fittings

Angle Compression Ball Valve — 316L Stainless

Angle Compression Ball Valve: 90° stainless steel ball valve with double-ferrule ends. FerruleX factory RFQ. Stocked sizes ship fast. Export RFQ only — no cart.

Brand
FerruleX
Material
SS316 / SS316L / SS304
Ends
Compression (double ferrule)
Pattern
Angle, 90°
Pressure
930 psi / 6.4 MPa

Request a factory quote

  • Stock5–7 days after confirmation
  • Make to order15–25 days production
  • Payment / termsT/T ~30% or L/C · FOB Shanghai / Ningbo
  • OEMLogo and drawings accepted · price on RFQ

Description

A crowded panel leaves no room for a valve and a separate elbow. The 90° body does both jobs: the outlet turns the run by a quarter, so you save one joint and one bend radius. That matters where a straight valve plus an elbow will not fit between neighbouring instruments. What you give up is the straight-through path: the flow turns inside the body, so this is not the pattern for a run that has to stay on axis. Rated 930 psi (6.4 MPa) with a working ceiling around 70 °C at ambient. Ferrule compression ends, bodies in 316, 316L or 304 stainless, sizes 3–25 mm and 1/8"–1". Check handle swing against the enclosure before the port positions are fixed.

Angle-pattern 930 psi (6.4 MPa) stainless ball valve with ferrule compression ends. The 90° body replaces a straight valve plus an elbow, saving one joint and one bend radius on a crowded panel. Flow turns inside the body rather than following a straight path. Sizes 3–25 mm and 1/8–1 in, ambient service with a working ceiling around 70 °C.

Body
90° pattern combines the valve and the elbow in one body.
Saving
One fewer joint and one fewer bend radius on a crowded panel.
Trade-off
Flow turns inside the body; an in-line run needs the straight pattern.
Materials
316, 316L or 304 stainless, sizes 3–25 mm and 1/8"–1".

Specifications

SpecificationValue
BrandFerruleX
MaterialSS316 / SS316L / SS304
EndsCompression, double ferrule
Tube OD3–25 mm / 1/8"–1"
PatternAngle, 90°
Pressure930 psi / 6.4 MPa at ambient
TemperatureAmbient; working ceiling around 70 °C

Request Quote

Prices stay on the RFQ. Send size, material, quantity and destination — the factory replies with price, lead time and packing. Packing, payment and the usual quote questions are on thedelivery pageand the FAQ.

Request a factory quote

Questions about this part

When should I fit the angle body instead of a straight valve?

When the run turns 90° at the valve and the gap is short. The angle body replaces a separate elbow, so the assembly loses one joint and one bend radius. The outlet direction is set before the nut is made up.

Is this a two-port valve or a diverting valve?

Two ports only: one inlet, one outlet, with the outlet at 90°. It shuts flow off or lets it through; it does not switch a stream between ports. L-port and T-port routing needs a three-way valve instead.

What service does the 930 psi rating cover?

It is a utility class rating at ambient: 930 psi, or 6.4 MPa. That suits utility lines such as instrument air or water. State the line pressure and the medium on the RFQ so the body class is confirmed.

What does the 70 °C ceiling rule out?

Steam, hot oil and any line that runs above that ceiling. The working limit is around 70 °C, so the valve is an ambient-service item. Above it the standard seat and seals are outside their rating, so ask before ordering for warm service.

Can I throttle with this valve?

Not for control. A ball valve is an on-off item: part-open flow passes across the seat edge and erodes it, and the handle gives no fine adjustment. Use it fully open or fully shut, and fit a control valve for modulation.

Does the closed valve trap pressure?

Yes. With both seats shut, fluid stays trapped in the body cavity, so vent or drain the isolated side before breaking any joint. Do not treat the closed valve as a bleed point on a line that is still live.

Related products