On the compression joint itself: no Teflon tape, no pipe dope. The ferrule seals by biting the tube wall, metal to metal, and any film on tube, ferrule, body or nut threads stops that bite. On the tapered pipe thread at the other end of the same adapter, tape or compound is what closes the leak path.
Key takeaways
- The compression joint seals by the ferrule biting the tube — metal to metal. Sealant on the tube, ferrule, body or nut threads prevents the bite; makers’ instructions say so verbatim.
- Grease on the sealing surfaces creates a “wet seal” that passes a short test, then migrates or slips under cycling and leaks later.
- The tube nut’s threads are not a pressure boundary — they only draw the ferrule into place. Taping them hides a bad make, nothing more.
- NPT/BSPT tapered ends need sealant on the male thread, kept off the first thread or two. BSPP parallel ends never seal on the thread — they seal at the face.
- The lubricant exception is narrow: the maker’s specified product on the maker’s named locations — never between ferrule and tube.
Which end are you sealing?
This argument never dies because both sides are half right. The split is positional, not preferential: it depends which end of the fitting is in your hand. Get the two ends confused and the classic failure follows — tested tight, weeping a month later.
| End on the drawing | Thread form | Seals at | Sealant? | What decides it |
|---|---|---|---|---|
| Compression tube end | Straight nut thread | Ferrule-to-tube metal bite | Never | The bite only happens metal to metal; any film stops it |
| NPT / BSPT male end | Tapered | Thread flanks plus compound | Yes — tape or dope, male thread only | Crests and roots never mate, so a helical path stays open |
| BSPP (G) male end | Parallel | Face: washer, O-ring or bonded seal | No — sealing element at the face | ISO 228-1 puts tightness in a seal other than the thread |
Read the row for the end you are making up. Where the seal is a metal-to-metal bite or a face element, the thread carries no sealing duty and tape only interferes.
How does a compression fitting actually seal?
A double-ferrule fitting seals at two metal interfaces. The front ferrule is driven into the body seat while its leading edge bites the tube OD; the back ferrule grips and anchors the tube. The mechanism is set out in single ferrule vs double ferrule fittings.
The tube nut’s threads do one job: convert wrench torque into axial drive. The thread annulus sits outside the sealed fluid volume, so it is not a pressure boundary. Makers’ instructions read almost identically: tubing clean, dry, deburred; no sealant or tape on tube, ferrules, body or straight threads.
A national-lab engineering standard states the same rule in one line. The full installation discipline is in how to install stainless steel compression fittings.
Check the joint before the nut moves:
- Tube end deburred; tube surface clean and dry at the ferrule position.
- No tape, dope or grease on tube, ferrules, body or straight threads.
- End form read off the drawing: compression tube end, NPT/BSPT male, or BSPP male.
- Sealing element present for a BSPP end: washer, O-ring or bonded seal.
- Lubricant to hand only if the instructions name it, and only for the named surfaces.
Why does dope on the ferrule backfire?
Grease on tube or ferrule is a boundary layer between surfaces that must fuse by controlled deformation. It cuts friction exactly where friction is the tool. The ferrule skates instead of biting and deforms unevenly — gripping one side of the tube, leaking on the other.
The film also wrecks torque feel, so normal wrench force drives the nut too far: crushed ferrule, collapsed tube, fitting pulled past its seat. A joint that feels tight has often not gripped at all.
The second failure is slower. A grease-filled joint passes a short static test because the compound temporarily fills the scratches where a leak path starts. Then vibration, cycling or thermal movement migrates the fill or shifts the ferrule, and the path opens at working pressure.
The repair is disassembly, not another quarter-turn: new ferrule, residue-free degrease, remake to spec, retest at service pressure. In-service diagnosis is in compression fitting leaks: causes and fixes.
| Symptom | Most likely cause | What to change |
|---|---|---|
| Passes a short test, weeps within a month | Grease or dope on tube or ferrule — a wet seal | Disassemble, new ferrule, residue-free degrease, remake to spec, retest |
| Feels tight, leaks from the first pressurisation | Ferrule skated on a lubricated surface and gripped unevenly | Clean and dry surfaces at the ferrule interface, new ferrule, remake |
| Crushed ferrule, collapsed tube, nut past seat | Lubricated threads hid the torque feel, so the nut was driven far | New ferrule and tube end, remake with dry surfaces |
| Leak along an NPT or BSPT thread | No tape or compound on the male thread | Coat the male thread, keep it off the first thread or two |
| Leak at a BSPP joint despite tape | Parallel thread does no sealing; tape holds the face element off | Remove the tape, seat the washer, O-ring or bonded seal, replace the washer |
| Tape strands found downstream of the fitting | Tape wrapped over the leading threads, or tape on the compression end | Keep sealant off the first thread or two; none on the compression end |
| Deformed threads, split brass female end | Wrenching past the point where the flanks wedge home | Make up within hand-tight plus about a turn |
Where sealant is right: the pipe thread end
The threaded end follows different physics. NPT is tapered: flanks wedge together as the joint tightens, but crests and roots never mate perfectly, leaving a helical leak path along the thread. Tape or compound fills that path and lubricates against galling.
Coat the male thread and keep sealant off the first thread or two so strands cannot enter the system. BSPT is the same story: a taper sealing on the flanks with approved compound.
BSPP is the opposite machine. The G thread is parallel and only clamps the parts together; the seal happens elsewhere — under a bonded washer, in an O-ring groove, on a machined seat.
ISO 228-1 itself defines pressure-tightness as coming from a seal other than the threads, so tape on a parallel flank seals nothing: the gap at the face leaks straight past it.
Wrenching past the point where the flanks wedge home only piles on interference and hoop stress: permanently deformed threads, split brass female ends. More force never improves the seal the taper already makes.
Deep dives: BSP thread seal and identifying NPT vs BSP threads.
What lubricant is allowed, and when?
One sanctioned use of grease exists, narrower than shop folklore. Some makers permit the supplied lubricant on the body threads and the rear face of the back ferrule of preswaged fittings — surfaces that transmit drive, not seal.
One major maker goes further both ways: its stainless procedure requires a specified anti-galling lubricant on the threads, its steel fittings none. No lubricant named in the instructions means none.
The constants: the specified product, on the named locations, ferrule-to-tube interface clean and dry.
How do you make it up, and what do you order?
- Step 1 — Read the end forms. Confirm each end on the drawing: compression tube end, NPT/BSPT male, or BSPP male with its face seal.
- Step 2 — Prepare the tube. Deburr it, then clean and dry it. No tape, dope or grease on tube, ferrules, body or straight threads.
- Step 3 — Add lubricant only if named. The maker’s specified product, on the maker’s named surfaces — never between ferrule and tube.
- Step 4 — Drive the ferrule. The nut threads turn wrench torque into axial drive; stop within hand-tight plus about a turn, where makers give turns from finger-tight, typically two to three through 3/4 inch sizes.
- Step 5 — Seal the pipe thread, then retest. Tape or compound on the male thread, off the first thread or two; on BSPP, seat the washer, O-ring or bonded seal instead. A remade joint deserves a retest at service pressure.
One line list, one quote: our compression fittings range quotes ends as separate lines. Send these four items.
-
end forms— one line per end: compression tube end (OD + wall), NPT/BSPT male (sealant-ready), BSPP (washer or O-ring boss, sealing element supplied). -
medium— gas or liquid, working pressure and temperature; gas forgives nothing at the ferrule. -
sealant policy— plants that ban tape strands (oxygen, analyzer, paint lines) should say so; we assemble to it. -
remake expectations— a remade joint deserves a retest at service pressure.
FAQ
Should I use Teflon tape on compression fittings?
No. The ferrule seals by biting the tube wall, metal to metal, and instructions forbid sealant on tube, ferrules, body and straight threads. Tape stops the bite and leaves a wet seal that leaks later.
What about thread sealant on the tube nut?
None. The nut threads only draw the ferrule into place and sit outside the sealed fluid volume, so they never see the medium. Tape masks an under-make, and stray strands migrate to the ferrule seat.
Do the NPT threads on the adapter end need tape or dope?
Yes, male thread only. A taper leaves a helical leak path; tape or compound fills it and limits galling on stainless, kept off the first thread or two. BSPT is the same; BSPP seals at the face.
The BSPP end came with a washer — do I still add tape?
No. A parallel G thread only clamps; the seal is at the mating face on the bonded washer, O-ring or machined seat supplied. Tape seals nothing and can hold the element off its seat, so replace the washer every remake.
Is any lubricant ever allowed during assembly?
Only the maker’s specified product, on the surfaces the maker names: usually body threads and the rear of the back ferrule on preswaged fittings. One maker requires an anti-galling lubricant on stainless threads. Never between ferrule and tube.
What torque should the threaded end actually get?
No universal number exists: the thread standard controls position, not torque. Make up hand-tight plus about a turn of wrench; makers give turns from finger-tight, typically two to three through 3/4 inch. Brass tables run near 70% of steel, maker-specific.



