Skip to content

Need stainless steel fittings, valves or hose?

BSP Thread Seal: Why BSPP Needs a Washer and BSPT Does Not

BSPP vs BSPT sealing: why parallel G threads need a washer or bonded seal, tapered R threads seal on the flank, plus bonded seal dimensions by size.

Mar 1, 2027 · 5 min read · FerruleX Factory

Stainless fitting end with sealing face, the part a BSPP washer seals against

A BSPP joint seals at the face; a BSPT joint seals on the thread. BSPP (G, ISO 228-1) is parallel, so its flanks carry no sealing duty — a washer, O-ring, bonded seal or machined seat closes the joint. BSPT (R, ISO 7-1) tapers 1:16 on diameter, so flank interference under sealant is the pressure boundary.

Choose the sealing method to match the thread form and the joint holds. Choose wrong — tape on a parallel thread, a washer on a taper — and you have built a leak that no amount of torque will close.

Key takeaways

  • BSPP (G, ISO 228-1) is parallel: the thread only holds the parts together; the seal happens at the face on a washer, O-ring, bonded seal or machined seat. ISO 228-1 itself defines pressure-tightness as coming from a seal “other than on the threads.”
  • BSPT (R, ISO 7-1) tapers 1:16 on diameter and seals on the flanks — by thread interference plus sealant. No washer exists in the joint.
  • PTFE tape cannot seal BSPP: it sits on flanks that are not the sealing surface. The gap at the face leaks straight past it.
  • The classic bonded-seal dimensions are a published series — match the seal to the standard series, not just the thread name, and treat bonded seals as single-use.
  • Stainless threads gall: lubricate, control torque, and replace the seal every re-make.

Which seal does my thread need?

Settle the thread form before you choose a seal. Both families share a 55° Whitworth flank profile and often arrive as “BSP” on a sketch, so the label alone does not tell you which sealing system you are holding.

Factor BSPP (G, ISO 228-1) BSPT (R, ISO 7-1) What decides it
Thread form 55° Whitworth, parallel 55° Whitworth, tapers 1:16 on diameter The drawing. The shared 55° flank identifies neither family on its own
Sealing surface The end face — bonded washer, O-ring, or a seat machined into the port The thread flanks, metal-to-metal under interference Decisive row: a tapered port has no face to seat a washer, a parallel port no taper to wedge
Sealant None. Tape sits on flanks that carry no pressure PTFE tape or paste, always Follows from the sealing surface, never from habit
Parts in the joint A washer is a component — DIN 3852 Form A closes on one No washer exists in the design A washer on the parts list means a parallel thread
Pressure boundary At the washer or the machined seat In the thread itself The row that tells you what to inspect when the joint leaks

The sealing-surface row decides it. A parallel port has a flat face to seat a washer and no taper to wedge; a tapered port has no face element at all. Match the seal to the form actually in your hand, not the form the sketch implied.

If the two are still indistinguishable at the bench, the measuring method is in how to identify NPT vs BSP threads.

How does each one seal?

BSPP (G): the face carries the seal

A G-thread joint is two jobs bolted into one. The parallel thread clamps the parts together and resists the load. The seal is made somewhere else entirely — under a bonded washer at the face, in an O-ring groove, or on a machined metal seat.

DIN 3852 stud-end forms name the variants precisely. Form A closes with a sealing washer under the collar, plain or bonded. Form B closes metal-to-metal on a cutting face machined into the port. Both are face seals; the thread is only the clamp.

Our printable BSPP thread chart carries the sizes and TPI, and states the same rule: parallel threads seal on the face, never on the flank. ISO 228-1 agrees — pressure-tightness comes from a seal other than on the threads.

BSPT (R): the thread is the seal

An R thread is the opposite machine. The 1:16 taper on diameter wedges male and female flanks together as the joint tightens. The flank contact, with PTFE tape or paste filling the gap, is the seal.

There is no face element to seat a washer on, so the thread is not merely a clamp: it is the pressure boundary. Always use a thread sealant on BSPT, and torque to a controlled value rather than “tight plus a grunt.”

That tape-or-paste rule is positional, and it flips at the other end of the same adapter. A fitting with a BSPT tail and a compression tube end needs sealant on the tapered thread and none at all on the ferrule side.

On the ferrule side, dope or tape stops the ferrule from biting — the classic signature of a joint that tested tight and wept a month later. The material-by-location rules are in pipe dope vs Teflon tape on compression fittings.

Which bonded seal fits my G thread?

Bonded seals — the metal-rubber washers sold under the classic Dowty heritage — are sized to the BSPP thread. The classic series is published identically by independent seal suppliers.

BSPP thread Seal ID (mm) Seal OD (mm) Thickness (mm)
G1/8 10.37 15.88 2.0
G1/4 13.74 20.57 2.0
G3/8 17.28 23.80 2.0
G1/2 21.54 28.58 2.5
G3/4 27.05 34.93 2.5
G1 33.89 42.80 3.2
G1-1/4 42.93 52.38 3.2
G1-1/2 48.44 58.60 3.2
G2 60.58 73.03 3.2

The dimensions above are the Dowty-type series. Metric and continental series differ in outside diameter for the same thread, so match the seal series to the drawing rather than improvising.

The thread dimensions themselves — TPI and major OD — are in the BSPP thread chart. The G sizes there and the seal sizes here share the same ISO 228-1 size names.

How do I assemble the joint?

Five steps cover both forms. The order matters less than the branch at step two: after that the two systems share nothing.

  1. Identify the thread form. G or R. Check TPI and major OD against the BSPP thread chart; the 55° flank alone identifies nothing.
  2. Branch at the seal. Parallel: bonded seal, O-ring, or the machined seat. Tapered: thread sealant. Nothing else closes either joint.
  3. Seat the element. BSPP: washer under the collar (Form A) or metal-to-metal on the Form B face. BSPT: sealant on the tapered thread only.
  4. Lubricate and torque. Anti-seize the stainless threads, then torque to the specified value rather than to feel.
  5. Renew the seal at every re-make. A bonded seal takes a set; a used one is a bought leak.

Stainless-on-stainless threads seize easily: the oxide film that protects the alloy shears under load and the clean metal welds microscopically — galling. Lubricate or anti-seize the assembly, torque to the specified value, and treat the seal as a consumable.

The full galling mechanics and the fastener-side fixes are in thread galling on stainless steel fittings.

What goes wrong, and what do I change?

Symptom Most likely cause What to change
Weeps at the face on first pressure PTFE tape on a parallel G thread — the flanks are not the sealing surface Remove the tape; fit the bonded seal, O-ring or seat the port was designed for
Still weeps with a new seal Port face scratched or scored — the rubber cannot ride over a groove Face condition first; 0.1 mm of damage on a machined seat out-leaks any seal
New seal, wrong fit at the face Continental series in a port drawn for the Dowty-type series Match the seal series to the face diameter on the drawing
Collar never clamps the seal, joint weeps Stud bottoms in the port before the collar loads the washer Let the collar, not the nose, set the stop
Threads seize during make-up Stainless-on-stainless run dry, or torque by feel Lubricate or anti-seize; torque to the specified value
Tight test passes, leak appears a month later Sealant carried onto the ferrule side, so the ferrule never bit Sealant on the tapered thread only; keep the ferrule side dry
Re-made joint leaks Bonded seal re-used after taking a set New seal at every re-make — treat it as a consumable

Work down the table. Face and seal faults come first, because they survive a correct torque figure. Assembly faults come last, and neither a new seal nor more torque fixes them.

What do I put on the RFQ?

One line can carry thread, form and seal. Use the patterns below and adapt them to the port you are actually holding.

  • G1/2 male stud, DIN 3852 Form A, bonded seal supplied — thread, form and seal in one line.
  • R1/2 male, thread sealant per assembly spec — for the tapered side.
  • 316, with anti-seize assembly — material and assembly note together.
  • Seal series when it matters: Dowty-type bonded seal, G1/2 versus the continental series.

Confirm each line before the drawing goes out:

  • Thread family and size — G1/2 (ISO 228-1) or R1/2 (ISO 7-1)
  • Stud-end form — DIN 3852 Form A (washer) or Form B (metal-to-metal)
  • Sealing element — bonded seal, O-ring or machined seat
  • Seal series — Dowty-type or continental, as drawn
  • Material and assembly note — 316, with anti-seize

Nothing on the RFQ compensates for fitting a washer to a taper or tape to a parallel thread.

FAQ

Can I use PTFE tape on BSPP threads? No. Fitting guidance is explicit that tape will not produce a pressure-tight BSPP joint — the flanks are not the sealing surface, so tape cannot bridge the face gap. Fit the bonded seal or O-ring the port was designed for.

Why does BSPT not need a washer? The seal is the thread itself. The 1:16 taper wedges the flanks into metal-to-metal contact as the joint tightens, and the sealant fills the microscopic spiral path. There is no face element and no cavity for a washer.

What is a bonded seal and when is it used? A flat metal washer with elastomer bonded to one face, the Dowty-type design. It seats under a DIN 3852 Form A collar, seals on the port face, and the ring carries the clamp — standard for parallel G-thread stud ends.

Are bonded seal dimensions universal? No. The Dowty-type series is tabulated above, but continental metric series differ in outside diameter for the same thread. Match the seal to the series on the drawing, and treat seals as single-use.

My BSPP joint still leaks with a new seal — what now? Check the port face: scored, the rubber cannot ride over a groove, and 0.1 mm of damage out-leaks any seal. Then the seal series against the face diameter, and whether the stud bottoms before the collar clamps.

Related: hex plug vs flush plug.

Related articles

More guides for stainless steel fittings buyers.