Skip to content

Need stainless steel fittings, valves or hose?

Can You Use Stainless Compression Fittings on Copper or Plastic Tubing?

When stainless steel compression fittings work on copper, nylon, PEX or PTFE tube — ferrule material rules, insert requirements, pressure limits, and the failure modes to avoid.

Sep 25, 2026 · 6 min read · FerruleX Factory

Stainless compression fitting on soft tubing with support insert

Sometimes. A stainless compression fitting can hold on copper or plastic tube, but the fitting’s material does not decide that on its own.

Three things decide it: ferrule material, tube hardness, and usually a support insert. Get any one of the three wrong and the joint leaks, creeps, or pulls out months after installation.

Key takeaways

  • A ferrule must be harder than the tube it bites, which is why fitting makers recommend brass ferrules — not stainless — on soft copper tube.
  • Plastic tubing such as nylon, PE, PP, PTFE and vinyl needs a metal fitting series approved for that tube plus a support insert sized by both OD and ID, or the joint creeps, weeps or pulls out under load.
  • The working pressure limit of a stainless fitting on any tube belongs to the complete assembly — fitting, ferrule, insert, tube, fluid and temperature — so the lowest-rated component sets the limit.

Which ferrule set does my tube need?

Fitting makers’ default guidance is to use like materials: stainless ferrules on stainless tube, brass on copper, plastic on plastic. The reason is mechanical. The ferrule must be harder than the tube so it can swage and lock, which is the principle behind the family covered by ISO 8434-1, metallic 24° cone connectors.

A brass ferrule on stainless tube never gets its full bite. A hard stainless ferrule on soft tube bites too aggressively.

The exceptions matter too. On copper tube, brass ferrules are the recommendation precisely because brass is a copper-zinc alloy — functionally a like material that grips without galling.

Sometimes you deliberately want a soft ferrule. A Teflon front ferrule with a nylon back ferrule seals around a thermocouple probe or glass tube without locking it in place or fracturing it.

Quick reference by tube type:

Tube Ferrule set Insert What decides it
Soft copper Brass ferrules (not stainless) Not normally Ferrule hardness against a soft wall
Nylon / PE / PP / vinyl Approved metal fitting + ferrule set Yes, size by OD + ID Insert availability and creep under load
PTFE Own approved arrangement Check maker — rigid tube Tube rigidity, not softness
PEX Own approved arrangement Check maker — do not assume soft-tube insert fits Fitting series approval, never the insert alone
Stainless Stainless ferrules No Like-on-like bite; no support needed

Can a stainless fitting go on copper tube?

The conservative rule from major fitting makers: on copper, use brass ferrules and bodies, not stainless. A hard stainless ferrule can score, oval or crack soft copper instead of seating cleanly, and several installation specs explicitly exclude stainless ferrules on copper tube.

If you must join stainless to copper — a mixed-metal instrument run, for example — use a fitting series the maker explicitly approves for that tube. Verify the copper’s hardness and wall thickness first.

Plan for galvanic corrosion at the joint in wet service. A dielectric separation or a sealed environment extends the life of any stainless-to-copper transition.

Brass on copper follows the domestic-plumbing convention (BS EN 1254-2), and the same-metal sliding risk behind thread galling in stainless steel does not apply. A ferrule is pressed radially into the wall, not slid under torque, and ductile, galling-resistant brass swages a clean bite.

The boundary is duty, not the pairing. Brass tops out near 3,000 psi where stainless instrument fittings reach 10,000, its temperature ceiling is hundreds of degrees lower, and ammonia service or dezincifying water attack the zinc in the alloy.

When does plastic tube need a support insert?

Several metal compression-fitting families are approved for plastics such as nylon, polyethylene, polypropylene, PTFE and vinyl. The approval holds with normal makeup procedure and a properly sized insert when required.

The insert is a sleeve that supports the tube ID, so the ferrule cannot collapse or creep the tube under load. Select it by both tubing OD and ID. A soft-tubing insert is not automatically right for rigid PEX or PTFE.

Check these before you order the insert:

  • Tube OD and ID both measured, not assumed
  • Fitting series approved for that specific plastic
  • Insert fitted wherever the maker requires one
  • PTFE: its own approved arrangement, rigid tube
  • PEX: do not assume a soft-tube insert fits
  • Temperature derating checked against the real fluid temperature

What pressure and temperature can the joint take?

There is no single rating for “stainless on plastic.” The working limit belongs to the complete assembly — fitting, ferrule, insert, tube, fluid and temperature together. Treat the lowest-rated component as the limit.

A 6,000 psi stainless body tells you nothing about a nylon tube run at 60 °C. Plastics soften, swell and creep with temperature, so the derating curve matters more than the headline number. Get the assembly rating from the maker for your actual conditions.

How do I make the joint, and what usually goes wrong?

  1. Confirm the tube. Material, hardness and wall thickness. On copper, verify hardness and wall thickness before you buy the fitting.
  2. Pick the ferrule set by tube material. Brass on copper, stainless on stainless, an approved set on plastic.
  3. Fit the support insert where required, sized by both OD and ID.
  4. Make up to the prescribed turns past finger-tight. Under-tightening here is one of the listed failure modes.
  5. Remake on a weep. Re-cut the tube past the grip marks and use a new ferrule set.

When a joint fails, the symptom narrows the cause:

Symptom Most likely cause What to change
Slow weep after weeks under load Plastic creep under the ferrule Remake with a new ferrule set; check temperature against rating
Tube pulls out under pressure Inadequate grip, or a missing insert Fit the insert sized by OD and ID; confirm the ferrule set
Leak at first make-up Under-tightening, or skipped turns Remake to the prescribed turns past finger-tight
Tube collapsed or flow restricted Insert omitted where one was required Add the insert, then remake
Tube scored or cracked Ferrule harder than the tube Move to brass on copper, or an approved series
Pitting in a damp enclosure Galvanic couple at a stainless-to-copper joint Dielectric separation or a sealed environment

What to send with the RFQ?

Tell FerruleX the tube material, OD and ID, the fluid, and the working pressure and temperature — not just the thread size. That is the difference between a fitting that holds and a callback.

We supply stainless compression tube fittings from male connectors to bulkhead unions. We flag when your tube calls for an insert, a brass ferrule set, or a different series entirely — send the duty and we quote it.

Include in the RFQ:

  • Tube material
  • Tube OD and ID
  • Fluid
  • Working pressure
  • Working temperature
  • Copper hardness and wall thickness, where copper is involved

FAQ

Can I put a stainless compression fitting on soft copper tube? Most manufacturers recommend brass ferrules on copper. Stainless ferrules risk scoring or ovaling the tube. Use an approved series if you must mix, and protect the joint from galvanic corrosion.

Do I always need an insert with plastic tubing? Use one whenever the fitting manufacturer requires it — typically on soft tubing. Choose it by tubing OD and ID.

Why did my plastic tube fitting leak after a month? The usual causes are creep under the ferrule, a missing or wrong-size insert, or temperature above the assembly rating. Re-cut the tube past the grip marks and remake with a new ferrule set.

Is PTFE tube treated like nylon? No. PTFE is rigid and needs its own approved fitting arrangement. Do not assume a soft-tubing insert fits it.

What if my tube is harder than the ferrule? Swap to a harder ferrule set or a series designed for hard tube. A soft ferrule on hard tube cannot swage, and the joint will pull out under pressure.

Can I use a brass compression fitting on brass tube? Usually, yes — brass ferrule sets are sold explicitly for brass, copper and iron tube. It is a like-on-like pair, and duty sets the boundary, not the pairing.

Related articles

More guides for stainless steel fittings buyers.