Air throttle valves settle an argument that pressure regulators cannot: how fast the cylinder rod moves.
Throttle the exhaust, not the supply. Fit a valve that meters one way and flows free the other. Mount it at the cylinder port and size it on bore and stroke time.
A rod that bangs out at full speed is not a pressure problem. Pressure sets the force, flow sets the speed, and the throttle valve is the flow knob. Turn the regulator down instead and you get a cylinder too weak to do its job while the rod still slams.
Key takeaways
- Pressure sets force; flow sets speed. The regulator answers “how hard,” the throttle valve answers “how fast.”
- Meter-out — throttling the exhaust — is the industry default because it damps stick-slip and controls overrunning loads; meter-in suits single-acting and small, light cylinders.
- A speed-control throttle is a needle plus a check valve: controlled flow in one direction, free flow in the other.
- Mount at the cylinder port for stability: less trapped volume between valve and piston means better response and repeatability.
- A cylinder that stays fast with the throttle nearly closed is telling you the valve is oversized, the load is light, the pressure is high — or the throttle is installed backward.
Which one do I need: meter-in or meter-out?
The choice is which side of the piston you choke. Meter-out throttles the exhaust: the supply fills the cap end freely, and the air leaving the rod end must squeeze through the throttle to govern the rod’s travel.
Pneumatic references call it the most common industry practice, and the reason is stability. Meter-out builds a back-pressure cushion that damps the stick-slip effect and holds an overrunning load in check. Meter-in can let the load run away faster than the circuit can fill.
Meter-in throttles the supply instead. Its proper territory is narrow: single-acting cylinders and small, short-stroke, light-load applications where the exhaust should be free.
| Control direction | What it throttles | Where it fits | Decisive factor |
|---|---|---|---|
| Meter-out | Exhaust leaving the rod end | Double-acting cylinders; overrunning or uneven loads | Whether the load can run away from the supply |
| Meter-in | Supply entering the cap end | Single-acting cylinders; small, short-stroke, light-load circuits | Whether the exhaust must stay free |
Specify the control direction on the RFQ — meter-out, rod extend — because it decides the valve’s internal orientation and the installation.
Needle valve or throttle with a check valve?
A plain needle valve is a restriction in both directions — simple, but it slows both the extend and the retract. The speed-control throttle adds a check valve in the same body: one direction passes through the needle and is metered, the reverse bypasses it and flows free.
Fitting the two functions into one body is what lets a single elbow at the cylinder port govern the working stroke while the return runs unthrottled.
This is the same component family as the push-to-connect versions used on panels, and the same one-way-flow logic appears across the valve catalog. The needle’s metering duty, and why it is not a pressure device, is covered in can a needle valve regulate pressure.
Where does the throttle go?
At the cylinder, not at the valve. Mounting the speed control directly on the cylinder port — the banjo-shaped pattern — is the most commonly used arrangement, and the engineering reason is the trapped volume.
The shorter the air column between the throttle and the piston chamber, the better the response, the adjustment sensitivity, the motion stability and the repeatability.
A throttle mounted back at the valve leaves a long tube of compressible air between restriction and piston, and that volume is a spring that fights your setting. The cylinder-port rule also puts the adjustment where the technician can reach it, at the actuator being tuned.
How do I size it?
Sizing is concept, not calculus: cylinder speed equals airflow divided by piston area — the references publish the relation as speed = flow rate over area.
A bigger bore moves slower on the same flow; more flow moves faster at the same bore. The throttle’s job is to set the flow, so the practical sizing line on the RFQ is the cylinder bore and the desired stroke time, and the selection is the throttle’s flow capacity plus its port size.
Under-size the throttle and the cylinder never reaches speed. Over-size it and you will be at the bottom of the adjustment range trying to slow a cylinder that physics wants to run fast.
The deeper needle-valve selection logic — fine-thread stems and small orifices for precision — is the instrumentation territory of the needle valves range, and the compression-side behaviour of these fittings is compared in quick-screw vs compression.
Why is the cylinder still fast?
Direction first, then sizing. A throttle that seems to do nothing is usually passing flow free in the stroke you meant to meter, or sitting outside the cylinder’s flow.
- Confirm the control direction. A throttle installed backward passes flow free in the direction you are trying to meter.
- Check the load for overrunning. Meter-in cannot hold it — move the control to the exhaust.
- Close the needle and watch the rod. Still fast with the needle nearly closed points to valve capacity, supply pressure, load or bore, not to more closing.
- Open the needle and watch the rod. Still slow with the throttle wide open points to an under-sized valve or low pressure.
- Re-check sizing against bore and stroke time before changing the valve.
| Symptom | Most likely cause | What to change |
|---|---|---|
| Rod still fast with the needle nearly closed | Valve over-size for the bore, high supply pressure, light load | Smaller flow capacity; re-check bore and stroke time |
| No change when the needle is turned | Throttle installed backward; check valve passing flow free | Re-orient so the working stroke is metered |
| Speed uneven, load runs away | Meter-in on an overrunning load | Move to meter-out on the exhaust |
| Cylinder slow with the needle wide open | Under-sized valve or low supply pressure | Larger flow capacity, or check the supply pressure |
What belongs on the RFQ?
control direction— meter-out (state which stroke) or meter-in; this orients the check valve.cylinder bore and stroke time target— the sizing inputs.flow capacity and port size— the selection pair that follows from them.connection— push-in for tube, threaded for ports; both sides.mounting— cylinder-port banjo style or in-line.
FAQ
Why is my cylinder still fast with a throttle valve fitted?
Check direction first: a backward check valve meters nothing. Then meter-in on an overrunning load, which cannot hold it. A needle nearly closed with the cylinder still fast points to valve capacity, supply pressure, load or bore.
Should I throttle the supply or the exhaust?
Meter-out, mostly. It is the industry default: the back pressure it builds damps stick-slip and holds overrunning loads. Reserve meter-in for single-acting and small, light, short-stroke work; state the stroke direction on the RFQ so the check valve orients correctly.
What is the difference between a needle valve and a throttle speed control?
A needle meters both directions — a restriction with no flow sense. A speed-control throttle adds a check valve in the same body: one direction metered, the reverse free. That is why it governs one stroke and still returns fast.
Why mount the throttle at the cylinder instead of at the valve?
At the valve, a tube of compressible air sits between restriction and piston, and that volume is a spring fighting your setting. At the cylinder port, response, sensitivity and repeatability are better, and the adjustment sits where the motion is.
Does a throttle valve replace a pressure regulator?
No. The regulator sets pressure and force; the throttle sets flow and speed. Turn the regulator down and the cylinder gets weak long before it gets smooth — regulator for force, throttle for motion.



