Cylinder connectors are the last fitting before the motion, and they take abuse the rest of the panel never sees: vibration at the rod end, flexing tube, hands-on maintenance and the wrong-thread emergency.
Match the connector to the port thread and to the motion. A compact metric cylinder with an M5 port and a moving rod end takes a push-in connector; a rigid run under severe continuous vibration takes compression.
The wrong thread does not fail at once. It walks loose under vibration, or cross-threads a port that looks fine until pressure finds it.
Key takeaways
- Port threads follow the cylinder’s design geography: M5 metric fine on compact metric cylinders, G threads on larger European/Asian designs, NPT on North American ones — small US cylinders may use 10-32 UNF.
- Parallel G ports seal at the face on an O-ring or bonded washer; tapered NPT and R threads seal on the flank with sealant. The thread’s job and the seal’s job are separate.
- NPT fittings do not belong in BSPP ports: 55° against 60° starts by hand, binds, and leaks or cracks the casting under pressure.
- Push-in connectors tolerate vibration and motion better than rigid threaded joints and are the automation default; for severe continuous vibration with rigid tube, compression is the stronger spec.
- The tube is the wear item at the cylinder — flex fatigue lives at the bend nearest the moving anchor, not at the fitting.
Which connector does my port need?
Two things decide it before the catalogue does: the port’s thread and the way the joint will move. The thread decides what screws in; the motion decides which of the three connection families survives there.
| Connection family | How the joint holds | Duty it suits | Typical leak mode | What decides it |
|---|---|---|---|---|
| Push-in quick-plug | spring collet grips the tube, elastomer seal; releases by collar | moving connections, re-route without cutting, end-of-arm tooling | tube scratched, oval or under-inserted | motion and service frequency |
| Compression | ferrule bites the metal tube | rigid tube under severe continuous vibration | under- or over-tightened | tube material and vibration severity |
| Threaded | sealant plus torque discipline | static or low-movement duty, joints not opened | under-torque or cross-thread | how often you open the joint |
None of the three is universally better. The choice is tube, duty and service frequency — the same conclusion the push-to-connect on stainless limits post reaches for the panel side.
Vibration is where the families separate. The rod end is the worst seat in the house for a rigid joint: vibration works threaded fittings micro-slip by micro-slip until the seal walks. That is why the comparisons rate rigid threaded connections for static or low-movement duty.
The spring-collet, O-ring-sealed push-in family sits comfortably ahead for moving connections. Automation end-of-arm tooling and cylinder ports are exactly that duty, which is why push-in is the default there. The push-to-connect range covers the flexible-run side of this joint.
One honest boundary. Where vibration is severe and continuous and the tube is rigid, ferrule-type compression rates higher than push-in — the metal bite holds where an elastomer seal chatters.
Whichever family you pick, support the tube so the fitting only seals. A connector asked to be a mechanical anchor fails early, whatever its brand.
What thread and seal is in the port?
Read the port before you order the fitting. Compact metric cylinders thread their ports M5, with M3 and M7 appearing on miniatures, and larger metric-design cylinders run G threads — parallel BSPP in ISO 228-1 sizes from 1/8 up.
North American cylinders run NPT, and the smallest US bores often use 10-32 UNF rather than metric. None of this is trivia: the port’s thread decides the connector’s thread, and guessing converts a five-minute swap into an adapter hunt.
| Port thread | Cylinder type | What the connector must match |
|---|---|---|
| M5 (M3, M7 on miniatures) | compact metric cylinders | M5 connector, face-sealed |
| G parallel BSPP, ISO 228-1 from 1/8 up | larger metric-design cylinders | G connector, face seal on an O-ring or bonded washer |
| NPT tapered | North American cylinders | NPT connector, flank seal with sealant |
| 10-32 UNF | the smallest US bores | UNF connector — confirm on the datasheet, not from the tube |
Sealing follows the same geography. A parallel G port seals at the face — an O-ring in the port face or a bonded washer under the shoulder, with the thread doing nothing but clamping. A tapered R or NPT port seals on the wedged flanks with sealant.
The full sealing logic is its own post — BSP thread seal: why BSPP needs a washer and BSPT does not — but at the cylinder the rule is immediate: identify the port thread, then match the connector’s thread and its sealing style. Our cylinder connector line covers the common port patterns.
What goes on the RFQ?
Order lines, not adjectives. These are the fields that choose the part:
port thread— M5, G1/8, 1/8 NPT: from the cylinder datasheet, not the tube.tube— size and material (PU or nylon), because the collet and the bend life both depend on it.connection family— push-in, compression or threaded, with the remake frequency expected.duty— static panel or moving actuator: the words that choose the family and the support hardware.sealing style— face seal on a parallel G port, sealant on a tapered NPT or R port: the port form dictates which.
How do you fit one so it stays sealed?
The order matters more than the torque figure. Work from the port outwards, and confirm the thread before anything is screwed in.
- Read the port thread off the datasheet. M5, G1/8 or 1/8 NPT comes from the cylinder, not from the tube in your hand.
- Confirm at the bench if the datasheet is missing. A thread pitch gauge plus the caliper routine in identify NPT vs BSP threads settles it in five minutes.
- Match the sealing style to the port form. Parallel G port: face seal, O-ring or bonded washer. Tapered R or NPT port: sealant on the flanks.
- Choose the family from the motion. Push-in for moving and frequently serviced connections, compression for rigid tube under severe continuous vibration, threaded for joints you do not plan to open.
- Support the tube, then trim it square. The fitting should only seal. On a push-in, a scratched or ovalled tube weeps past the seal — cut square and insert to the stop.
What goes wrong, and what do you change?
| Symptom | Most likely cause | What to change |
|---|---|---|
| Fitting walks loose under vibration | rigid threaded joint on moving duty | move to push-in, or compression where the tube is rigid and vibration is severe and continuous; support the tube |
| Joint leaks or cracks the casting under pressure | NPT forced into a BSPP port — 60° against 55° | use the port’s thread, or a purpose-made adapter |
| Push-in weeps after rework | tube scratched, oval or under-inserted | trim the tube square and re-insert to the stop |
| Fitting never seals again after a rebuild | a cross-threaded past has left damaged crests | replace the fitting |
| Compression joint leaks | under- or over-tightened | remake with torque discipline and a consumable ferrule |
| Tube splits near the moving anchor | flex fatigue at the bend; nylon transmits vibration where PU absorbs it | trim or replace the tube, keep the fitting |
The last row is the one that gets misdiagnosed. Fatigue lives at the bend nearest the moving anchor, not at the fitting, and the tube is the wear item at the cylinder.
FAQ
Can I use NPT fittings on a BSPP cylinder port?
No. NPT is 60° tapered, BSPP 55° parallel: the threads start by hand, then bind or strip, and even NPT into BSPT mismatches flank angle. Use the port’s thread or a purpose-made adapter.
What thread is on my cylinder port?
Read the datasheet first, measure second. Compact metric cylinders thread M5, larger metric designs run parallel G, North American cylinders run NPT, the smallest US bores often 10-32 UNF. A pitch gauge and caliper settle it in five minutes.
Push-in or compression at the cylinder?
Push-in for moving and frequently serviced connections: the release-collar remake and elastomer seal tolerate rod-end vibration. Compression for rigid tube under severe continuous vibration, where the metal bite outlasts the seal. Threaded for joints that should never move.
Why does my cylinder fitting keep leaking after rework?
Two suspects. A scratched or ovalled tube weeps past any push-in seal — trim it square and re-insert to the stop. Or a fitting previously forced across mismatched threads carries damaged crests and never seals again: replace it.
What actually wears out at the cylinder port?
The tube, not the fitting. Flex fatigue concentrates at the bend nearest the moving anchor, and abrasion and aging follow the motion. Inspection-led maintenance: check the tube runs, trim or replace the tube, reuse the fitting.



