Skip to content

Need stainless steel fittings, valves or hose?

Ferrule — FerruleX stainless steel fittings

Stainless Steel Ferrule — Types, Sizes & Specs

Stainless ferrule for compression fittings. SS304/316. FerruleX factory RFQ. Stocked sizes ship fast.

Brand
FerruleX
Material
SS304 / SS316
Type
Compression ferrule
Size
Match tube OD / series on RFQ

Request a factory quote

  • Stock5–7 days after confirmation
  • Make to order15–25 days production
  • Payment / termsT/T ~30% or L/C · FOB Shanghai / Ningbo
  • OEMLogo and drawings accepted · price on RFQ

Description

A ferrule is one of three parts in a compression joint, with the body and the nut. Slid onto the tube along with the nut and pushed into the body, it is driven forward as the nut is tightened: the front outer face seats against the body cone and the inner edge bites evenly into the tube wall, and that bite is where the seal forms. Tube stock should meet ASTM A269 or GB/T 14976; fully annealed tube under HRB 90 or HV 190 seats more predictably. Push the tube to the bottom of the body, and where a bend sits close to the joint leave more than 10 mm of straight tube outside the nut. Available in 304, 316 and 316L, Φ3–Φ25 mm and 1/8–1 inch, with M5–M24 threads.

A ferrule is ordered against tube OD and the nut series it will sit in, not against a pipe size. Give the tube OD in millimetres or inches, the grade, and whether the tube is fully annealed; both decide how the bite behaves.

Bite
The inner edge is driven into the tube wall evenly, and that bite makes the seal.
Cone
The front outer face bears on the body cone as the nut is drawn down.
Tube
Fully annealed stainless tube under HRB 90 or HV 190, to ASTM A269 or GB/T 14976.
Range
Φ3–Φ25 mm and 1/8–1 inch tube, in 304, 316 or 316L.

Specifications

SpecificationValue
BrandFerruleX
MaterialSS304 / SS316
TypeCompression ferrule
SizeMatch tube OD / series on RFQ

Request Quote

Prices stay on the RFQ. Send size, material, quantity and destination — the factory replies with price, lead time and packing. Packing, payment and the usual quote questions are on thedelivery pageand the FAQ.

Request a factory quote

Questions about this part

Does the ferrule have to match the body and nut series?

Yes. A ferrule is sized to one body and nut series, and the front and rear ferrules are a matched pair. Do not swap ferrules between series, even where the tube OD is the same.

Which tube does the ferrule bite into most reliably?

Fully annealed stainless tube under HRB 90 or HV 190, to ASTM A269 or GB/T 14976. A work-hardened wall resists the bite and the seal becomes less predictable, so confirm the tube condition on the order.

Must the tube be pushed fully home before the nut is tightened?

Yes, to the bottom of the body. The ferrule then bites just above the tube end, leaving no dead pocket behind the bite. Near a bend, leave more than 10 mm of straight tube outside the nut.

How far should the nut be tightened?

Draw the nut down until the ferrule is driven against the body cone and the tube can no longer be turned or pulled by hand. Stop there; further turning adds nothing to the bite.

Do the body threads gall when the joint is tightened?

Stainless on stainless can gall under load, and a seized nut stops before the bite is set. A thin film of anti-seize on the body threads and the nut thread keeps the make-up smooth.

Can the ferrule be reused when the joint is remade?

No. The bite is formed once and the used ferrule keeps that impression, so a second make-up seats unevenly and may leak. Fit a new ferrule each time the joint is opened.

Related products