Skip to content

Need stainless steel fittings, valves or hose?

Male-Female Elbow Adapter — FerruleX stainless steel fittings

Stainless Steel Male-Female Elbow Adapter — Sizes

Male-Female Elbow Adapter: 90° stainless steel pipe fittings changing thread gender/standard. FerruleX RFQ. Stocked sizes ship fast. Export RFQ only — no cart.

Brand
FerruleX
Material
SS304 / SS316
Type
Male-female elbow adapter
Threads
NPT / G / Metric
Order mode
Factory RFQ

Request a factory quote

  • Stock5–7 days after confirmation
  • Make to order15–25 days production
  • Payment / termsT/T ~30% or L/C · FOB Shanghai / Ningbo
  • OEMLogo and drawings accepted · price on RFQ

Description

A square body, one male nipple and one female port on adjacent faces, so the run turns a right angle and changes thread in the same make-up. Threads are cut in ZG(R), NPT, G or M form across 1/8 in to 2 in and M5 to M36, from 304 or 316 bar. Pressure is quoted around 3000 psi for liquid and gas, and the lower-rated end sets the limit once both are named. Flats on the body hold a wrench while the second thread is pulled up. The male end decides where the female port points, so choose that end first; tightening the second joint afterward carries torque back through the body.

Male nipple and female port on adjacent faces of one square body, turning the run through a right angle. Threads in ZG(R), NPT, G or M over 1/8 in to 2 in and M5 to M36, in 304 or 316, around 3000 psi for liquid or gas. The male end sets the direction.

Body
Square section, male nipple and female port on adjacent faces.
Threads
ZG(R), NPT, G or M form, mixed between the two ends.
Sizes
1/8 in to 2 in and M5 to M36, one size each end if needed.
Rating
Around 3000 psi for liquid or gas, limited by the lower-rated end.

Specifications

SpecificationValue
BrandFerruleX
MaterialSS304 / SS316
TypeMale-female elbow adapter
ThreadsNPT / G / Metric
Order modeFactory RFQ

Request Quote

Prices stay on the RFQ. Send size, material, quantity and destination — the factory replies with price, lead time and packing. Packing, payment and the usual quote questions are on thedelivery pageand the FAQ.

Request a factory quote

Questions about this part

Can the two ends use different thread forms?

Both ends are cut to order, so the male nipple and the female port can each be ZG(R), NPT, G or M form, and they need not match. Name the male end first and the female end second on the RFQ.

Do I give thread size or nominal pipe size?

Give the thread size for each end separately, not one nominal pipe size for the whole body. The male nipple and the female port are cut independently, so 1/8 in to 2 in and M5 to M36 may be mixed across the two.

What sealant goes on the threads?

PTFE tape or a thread paste on the male taper only, kept clear of the first thread so no tape enters the bore. Stainless against stainless galls, so a paste with anti-seize is the safer choice on repeated make-up.

Can the elbow be re-angled after tightening?

No. A tapered thread seats where it stops, so the body finishes at whatever angle that end reaches. Position the male end first, then bring the female run to the port rather than backing the body off to correct the turn.

What if the male end does not match my equipment port?

Then the male end is cut to the port you have, provided the form and size sit inside the range this body covers. Send the port thread and we match it, rather than an extra adapter going in line.

What temperature can this adapter take?

The limit follows the sealant or gasket used at the joint and the body grade chosen, so no single figure covers every assembly. Tell us the service temperature with the RFQ and the grade is quoted to suit.

Related products