Skip to content

Need stainless steel fittings, valves or hose?

Stainless Steel Precision Tube — FerruleX stainless steel fittings

Stainless Steel Precision Tube

Stainless Steel Precision Tube: tight-tolerance instrumentation tube for ferrule seals. FerruleX factory RFQ. Stocked sizes ship fast. Fast stock shipping.

Brand
FerruleX
Material
SS304 / SS316 / SS316L
Type
Precision tube
Use
Instrumentation
Order mode
Factory RFQ

Request a factory quote

  • Stock5–7 days after confirmation
  • Make to order15–25 days production
  • Payment / termsT/T ~30% or L/C · FOB Shanghai / Ningbo
  • OEMLogo and drawings accepted · price on RFQ

Description

From 1/8 in to 1 in OD (3.175 mm to 25.4 mm) and across a 3 mm to 25 mm metric series, this tube is bright annealed to a soft temper that will bend in the run. Both joint types are listed: welding, and ferrule fittings that grip the OD. The factory figure for working pressure is about 1200 psi. Listed applications run through environmental and energy plant, automotive and shipbuilding, petrochemical, construction, food processing and pharmaceutical work. Cut the end square and deburr before a ferrule is made up, since the seal sits on the OD surface. Wall and length follow the drawing; grade is 304, 316 or 316L. State OD, wall, grade and joint on the RFQ.

Bends come off an annealed tube cleanly, but the ferrule seat needs a straight, square-cut end with the OD untouched by the saw. Leave a straight length at each joint before the first bend. 304, 316 and 316L are all production grades; OD runs 3.175 mm to 25.4 mm, pressure about 1200 psi.

Size range
1/8 in to 1 in OD (3.175 mm to 25.4 mm), with a 3 mm to 25 mm series alongside.
Temper
Bright annealed and soft, so the tube bends in the run.
Joints
Welding and ferrule fittings are both listed for this tube.
Pressure
The factory figure is about 1200 psi for the tube itself.

Specifications

SpecificationValue
BrandFerruleX
MaterialSS304 / SS316 / SS316L
TypePrecision tube
UseInstrumentation
Order modeFactory RFQ

Request Quote

Prices stay on the RFQ. Send size, material, quantity and destination — the factory replies with price, lead time and packing. Packing, payment and the usual quote questions are on thedelivery pageand the FAQ.

Request a factory quote

Questions about this part

Is the tube bright annealed or polished?

Bright annealed, so the surface is the annealed finish off the mill rather than a polished one. That suits an instrumentation run where the ferrule grips the OD and the bore carries the medium. State if a polished finish is needed when ordering.

How tight can the tube be bent in the run?

The soft temper bends cleanly, but keep the bend clear of the ferrule seat and leave a straight length at each joint. A tighter bend collapses the bore and ovalises the OD, which ruins the seal.

Is the tube supplied in coils or straight lengths?

Both forms are quoted on the factory list, and the run usually decides which. Coils suit a long continuous line with few joints; straight lengths suit short runs and a square-cut end at each fitting.

How are the tube ends protected before installation?

Ends are capped for shipment so the bore stays clean and the OD is not nicked in transit. Cut square and deburr before the ferrule is made up, since the seal sits on the OD surface.

Is the tube specified by OD and wall or by pipe size?

By OD and wall. The size range runs from 1/8 in to 1 in OD with a metric series alongside, and wall follows the drawing. Nominal pipe size does not apply to this tube.

How tight is the OD and wall tolerance?

Tolerance is held on the drawing rather than a single stock figure, because the ferrule grips the OD and a slack tolerance shows up as a poor seal. Give the fit that matters on the RFQ.

Related products