Skip to content

Need stainless steel fittings, valves or hose?

NACE and Sour Service: When H2S Changes Your Material List

NACE MR0175 / ISO 15156 sour service basics: when the rules apply, hardness limits by alloy family, duplex envelopes, and the four numbers that decide the material.

Aug 23, 2027 · 6 min read · FerruleX Factory

Stainless fitting for sour service review, where hardness and condition decide eligibility

NACE MR0175 — now published jointly as ISO 15156 — is why a perfectly good 316 fitting can be wrong for the same fluid once H2S enters it. Sour service does not change what the alloy is; it changes what condition the alloy is allowed to be in.

The switch happens at about 0.3 kPa (0.05 psi) H2S partial pressure in the gas phase. Above that line the alloy name stops being the answer: hardness, heat-treatment state, cold-work history and the certificate decide the material list.

A certificate that says only “316” answers none of the questions the standard asks. For oil-and-gas buyers this is the gate every wetted part walks through.

Key takeaways

  • The rules bite when H2S partial pressure passes about 0.3 kPa (0.05 psi) in the gas phase — below that, MR0175 generally does not apply.
  • Austenitics like 316L serve under limits: solution-annealed condition, with procurement practice capping hardness at about 22 HRC; the standard’s own austenitic table centers on the solution-annealed state near 253 HV.
  • Duplex 2205 is conditionally qualified inside a published envelope — chloride, pH, temperature and H2S partial pressure all draw its boundary; nickel alloys carry the severe sour frontier.
  • Hardness is the compliance lever, and it collides with cold forming: cold-drawn tube and heavily worked fittings must be verified, not assumed.
  • The RFQ carries four numbers — H2S partial pressure, chloride, pH, temperature — and they, not the alloy name, decide the material list.

Which material do I need?

The answer is never a family name on its own. Each family enters sour service on its own terms, and the honest summary is conditional for all of them. Read the decisive column, not the alloy column.

Family What it needs to qualify Limit in practice What actually decides
Austenitic 316L solution-annealed, quenched hardness about 22 HRC; published table centred near 253 HV whether the part actually ships solution-annealed
Duplex 2205 solution-annealed, water-quenched, ferrite balance verified hardness near 28 HRC in the common editions; one sourced envelope near 3% chloride, pH 3.5 minimum, 150 °C maximum all four environmental numbers inside one envelope
6-Mo alloys case-by-case qualification resists H2S better than 316, but no blanket approval how severe the specific duty is
Nickel alloys full qualification carries the severe-sour frontier above the duplex envelopes combined sour-plus-seawater duty

Duplex numbers move between revisions, and later editions allow more hardness for some duplex grades. Verify against the current edition before the drawing is released.

Does the standard apply to my duty?

MR0175/ISO 15156 is the materials rulebook for oil and gas production with hydrogen sulfide in the stream. Its applicability gate is quantitative.

Once H2S partial pressure in the gas phase passes roughly 0.3 kPa — 0.05 psi — at operating pressure, the standard’s material restrictions apply. Below that line, its sour provisions generally do not.

Three conditions have to hold: H2S partial pressure above the gate, an aqueous phase present, and operating pressure above the low threshold. Below the gate, ordinary material rules stand. Re-run the test after any process change that adds H2S or raises pressure.

Above the gate, severity is mapped through four environmental inputs — H2S partial pressure, in-situ pH, chloride and temperature. Each material family carries its own envelope inside that map.

The failure mode the whole apparatus exists to prevent is sulfide stress cracking. Hydrogen absorbed at the corroding surface embrittles high-strength microstructures, and the crack needs no visible corrosion to run. Hence the obsession with one property — hardness.

Where does each family’s envelope stop?

316L is the default CRA for moderate sour duty. It is acceptable under ISO 15156-3 when supplied solution-annealed and quenched, and procurement practice caps hardness at about 22 HRC. The published austenitic table centres on the solution-annealed state near 253 HV rather than a blanket HRC number.

Its envelope is the modest corner of the map: low H2S partial pressure, moderate temperature. Outside it, the standard points to the next family.

Duplex 2205 is conditionally qualified, inside a published envelope that bounds chloride, pH, temperature and H2S partial pressure together. One sourced envelope puts the 22Cr duplex near 3% chloride, pH 3.5 minimum, 150 °C maximum and H2S around 0.02–0.1 bar depending on chloride.

Hardness practice caps near 28 HRC in the common editions, with later editions allowing more for some duplex grades. The steel must be solution-annealed and water-quenched, with ferrite balance verified.

6-Mo and nickel alloys sit one step above. Nickel alloys carry the severe-sour frontier where duplex envelopes end. 6-Mo alloys resist H2S better than 316 but are not blanket-approved across sour conditions.

The references steer combined sour-plus-seawater duty toward super duplex or nickel alloys precisely because those carry full qualification. The chloride side of sour duty overlaps the territory of chloride stress corrosion cracking, and the family selection logic sits in the grades field guide.

Why does hardness decide compliance?

Every line of MR0175 lands on the same property: hardness. The carbon-steel clause is the template — a hard ceiling of 22 HRC applied to base metal, weld metal and heat-affected zone alike, with single over-limit readings counting as non-conformance.

Austenitic and duplex families carry their own ceilings and conditions, and nickel alloys rate higher still.

The practical collision is with cold forming. Cold-drawn tube and heavily worked fittings gain strength and hardness exactly where the standard draws its line, so sour-service procurement verifies hardness on the finished condition of the part — not the mill’s annealed promise.

A drawing that specifies hard-drawn tube and an MR0175 duty on the same line is a specification argument waiting to happen.

What goes wrong in review?

Most rejections repeat the same handful of failures. The symptom shows up at incoming inspection or at the first crack; the cause is nearly always a condition line that was never written.

Symptom Most likely cause What to change
Certificate reads “316” with no condition stated the datasheet answered only the alloy question add solution-annealed condition and hardness certificate
One hardness reading over the cap cold-worked or hard-drawn finished part change the forming route, or verify hardness on the finished part
Duplex approved on chloride alone envelope read on one axis check chloride, pH, temperature and H2S together
Crack with no visible corrosion loss sulfide stress cracking of a high-strength microstructure bring hardness under the family cap
Sour plus seawater duty routed to 316 combined duty never written on the RFQ route to super duplex or nickel alloys
Fitting rejected at incoming inspection the mill’s annealed promise used as finished-part hardness hardness-verify part by part

How do I write a sour service RFQ?

Four numbers carry the material decision. Write them and the alloy follows.

  1. State H2S partial pressure in the gas phase. Below about 0.3 kPa (0.05 psi), the sour provisions generally do not apply and the RFQ can stop there.
  2. Add chloride content. It is the second axis of every envelope.
  3. Add in-situ pH. Severity regions are drawn in pH–H2S space.
  4. Add temperature. It is the fourth envelope boundary.
  5. Name the family the envelope allows, then write the condition line.

The condition line, on the austenitic or duplex route, carries five items:

  • solution-annealed condition, hardness certified
  • hardness verified on the finished part, not on the mill’s annealed promise
  • ferrite balance verified, duplex route
  • current edition of the standard cited on the drawing
  • NACE MR0175 / ISO 15156-3 compliant with certificate, where the duty demands it

The material name alone buys nothing in sour service. The condition and the certificate buy everything.

FAQ

Is 316 always OK in sour service?

No. 316 and 316L are acceptable only in solution-annealed condition, below the hardness cap, and inside an envelope of low H2S partial pressure and moderate temperature. Outside that, the standard points to duplex or nickel alloys.

What actually triggers NACE requirements?

H2S partial pressure: about 0.3 kPa (0.05 psi) in the gas phase, with an aqueous phase present and operating pressure above the low threshold. Pass all three and the sour provisions apply. Below the gate, ordinary material rules stand.

Can I use duplex 2205 fittings in sour service?

Conditionally. 2205 carries a published envelope bounding chloride, pH, temperature and H2S partial pressure, and it must arrive solution-annealed, water-quenched and hardness-verified. Inside the envelope it is the workhorse; outside, the references route to nickel alloys.

Why does cold-drawn tube fail NACE review?

Because cold drawing raises strength and hardness — the property the standard caps — and review reads the finished condition. Heavily worked product must be hardness-verified part by part, and often is not eligible at all.

What numbers decide my material for sour duty?

Four: H2S partial pressure, chloride content, in-situ pH and temperature. The envelopes are drawn in exactly those axes, and every compliant material list is a point inside a family envelope.

Related articles

More guides for stainless steel fittings buyers.