Galvanic corrosion is the bill that arrives when two metals share a wet bolted joint: one of them, the less noble, dissolves to protect the other.
The rule fits in two clauses. Nobility order picks the victim, area ratio picks the speed. Stainless threaded into carbon steel means the steel corrodes; 304 against 316 draws nothing worth acting on; a genuinely dry joint couples indefinitely.
Mixed-metal systems are everywhere — a stainless fitting on carbon steel pipe, a brass valve against stainless tubing, zinc-plated hardware on a stainless flange. The rule that predicts which piece pays is older than the fittings catalog and skipped more often than any other page in corrosion engineering.
Key takeaways
- In a chloride electrolyte the nobility ladder runs, roughly: graphite, titanium, passive 304/316, Monel and copper-nickel, then bronzes and brasses, then carbon steel, galvanized steel/zinc, then aluminum and magnesium at the active end.
- Stainless appears twice on the ladder — noble when passive, far less noble when its film breaks in a crevice or under deposits — and chlorides are what move it.
- The area rule decides severity: small anode against large cathode corrodes fast; the fastener rule follows — make the small part the more noble metal.
- Stainless on carbon steel means the steel corrodes; 304 against 316 is technically dissimilar and practically a non-issue.
- Dry indoor mixed systems are largely immune; wet systems need isolation — dielectric gasket, sleeves and washers, or coat the nobler metal, never only the anode.
Which mixed joints need isolation?
The decision is not “mixed metals or not”. It is which side is the small one, and whether the joint stays wet. Both questions have an answer before the drawing is released.
| Joint you are building | Which metal corrodes | What actually decides it |
|---|---|---|
| Stainless fitting screwed into carbon steel pipe | The carbon steel, preferentially and faster than it would alone | The pipe is the large anode, so the sacrifice spreads thinly — workable where the pipe’s loss budget allows, a maintenance item where it does not |
| Carbon steel bolt in a stainless flange | The carbon steel, quickly | Small anode facing a large cathode; the fastener rule says make the small part the more noble metal |
| Stainless bolt in a carbon steel flange | The carbon steel, slowly | The area ratio runs the safe way, with the steel as the large partner |
| 304 against 316 | Neither, in normal service | The series gap is too small to draw a practical current |
| Copper alloy beside stainless | The copper alloy, generally slowly | The series gap is moderate, so severity rides on area ratio and electrolyte |
| Stainless flange with a chloride-wet gasket crevice | The stainless itself | The oxide film has broken, so the metal sits at the active end of its own pair |
The 304-to-316 row is where buyers spend worry they do not need to spend. The two grades are technically dissimilar, and close enough on the series that direct contact draws no practical current.
Corrosion references call the pairing a non-issue in normal service. Each grade remains independently vulnerable to its own enemies, chloride pitting for 304 included, but neither sacrifices to the other.
The last row is the one that gets missed. A stainless flange whose gasket crevice goes chloride-wet can sit at the active end of its own pair, corroding against a partner it would otherwise protect.
How do I read the galvanic series?
The nobility ladder in seawater-type electrolytes is the map every mixed joint is read against. From the noble end down:
- Graphite
- Titanium
- Passive stainless — 304 and 316 with their oxide film intact
- Monel and the copper-nickels
- The bronzes, brasses and coppers
- Nickel, in its active state
- Cast iron and carbon steel
- Stainless, again — in its active state
- The aluminum alloys
- Galvanized steel and zinc
- Magnesium
The map’s most useful surprise is stainless’s double entry. The same steel that sits near titanium when passive drops to just above carbon steel when the film breaks — in a crevice, under a deposit, in a stagnant oxygen-starved corner.
Chlorides are the usual agent that moves it, per the crevice mechanics in pitting corrosion in stainless steel fittings. Design the joint for the position your stainless actually occupies, not the one the datasheet implies.
Why does the area ratio decide severity?
The nobility order picks who corrodes; the area ratio picks how fast. A small anode feeding a large cathode concentrates the galvanic current on a tiny surface, and the attack that follows is rapid, severe and localized.
The fastener rule is the codification of that: make the small part the more noble metal. Hence the asymmetry — a carbon steel bolt in a stainless flange corrodes fast, while a stainless bolt in a carbon steel flange is generally fine.
Where the geometry is fixed the other way, with the stainless fitting as the small part screwed into the steel pipe, the pair stays acceptable. The large anode spreads its sacrifice thinly.
What you must not build is the reverse: small steel part, noble large partner, wet joint.
No numeric threshold governs the ratio — the references state the principle qualitatively — so the rules of thumb above are the working guide.
What goes wrong at a mixed joint?
Read the symptom first, then the cause, then the single thing to change.
| Symptom | Most likely cause | What to change |
|---|---|---|
| Small steel part pitting through beside a stainless valve | Small-anode geometry: a little anode feeding a large noble cathode | Replace the small part with the more noble metal, or isolate the pair with a dielectric kit |
| Zinc-plated fastener eaten first on a stainless flange | Zinc sits at the active end of the ladder and is the small part | Treat it as sacrificial by design, or isolate the fastener |
| Steel pipe wall thinning beside a stainless fitting | The steel is the anode to the stainless cathode | Budget the loss against the pipe allowance, isolate where it does not fit; any coating goes on the stainless |
| Pitting starting under a gasket on a stainless flange | The crevice went chloride-wet, the film broke, and the stainless turned active | Keep the crevice dry and chloride-free — drainage, not alloy |
| Fastener corroded while the flange face is clean | A dielectric gasket was fitted, but the bolt path still completes the circuit | Add insulating sleeves and washers across the fasteners |
| Attack concentrated at one pinhole in a coated joint | The coating went on the anode only | Move the coating to the cathode; a pinhole in a coated anode manufactures the small-anode case |
The first two rows are area-ratio faults, and they survive every coating and every torque figure. The last row is created by the coating itself.
How do I isolate a mixed joint?
Galvanic corrosion needs an electrical path and an electrolyte. Break either and the cell dies.
- Step 1. List every metal in the wetted joint — pipe, valve, gasket and fasteners. The fitting alone is not the pair.
- Step 2. Place each metal on the seawater ladder above. Record whether your stainless is passive in this service, or active because a crevice or a deposit takes its oxygen away.
- Step 3. Find the small part, and check which way the area ratio runs. Make the small part the noble one; where the geometry is already fixed against you, isolate.
- Step 4. Break the electrical path: a dielectric gasket with insulating sleeves and washers across the fasteners. The gasket alone leaves the bolt path live.
- Step 5. Protect the cathode, then the electrolyte. Where only one metal is coated, coat the cathode; in closed systems, inhibitor dosing does the same job chemically; and set the drainage so the joint does not sit wet.
The dry-indoor caveat deserves respect in both directions. Genuinely dry service couples metals indefinitely without a cell.
Condensation films under insulation and humid-plant moisture are electrolyte enough to run a slow cell, which is why the insulation jacket matters, per the CUI logic in chloride stress corrosion cracking.
What goes on the RFQ at a mixed joint?
One line per item. The fitting is only one of them, and the pair is decided by the rest.
-
the full material list— every metal in the wetted joint, not just the fitting: pipe, valve, gasket, fasteners. -
electrolyte— water quality, chloride, immersion or atmospheric; the words that set the risk. -
isolation hardware— dielectric gasket with sleeves and washers, where the pair demands it. -
coating— the cathode, named, if coating is the mitigation.
Nothing on the RFQ compensates for a small steel part facing a large stainless one in a wet line. Send the joint, not the fitting: contact the factory with the full material list.
FAQ
Is 304-to-316 a galvanic pair? Technically yes, practically no. The two grades sit close enough on the galvanic series that direct contact draws no significant current, and references treat the pairing as a non-issue in normal service. Each keeps its own vulnerabilities.
What happens when I thread stainless into carbon steel? The carbon steel is the anode: it corrodes preferentially, usually faster than it would alone, while the stainless is cathodically protected. Where the pipe is the large partner, the sacrifice spreads thinly. Steel is the piece that pays.
Does galvanic corrosion happen indoors? Only where an electrolyte exists. Dry indoor service couples dissimilar metals indefinitely without a current, but condensation films, washdown spray and humid-plant moisture are electrolyte enough to run a slow cell, especially under insulation.
How do I stop galvanic corrosion at a mixed flange? Break the electrical path with a dielectric gasket plus insulating sleeves and washers; the gasket alone leaves the bolt path live. Where you coat, coat the cathode, never only the anode. Keep the joint drained and dry.
Why is my small steel part pitting next to the stainless valve? Classic small-anode geometry: a little steel component feeds a large noble cathode, so the current concentrates and pits it through ahead of schedule. Replace the small part with the noble metal, or isolate the pair.



