Cv is the valve flow coefficient: the number of US gallons per minute of 60 °F water that flows through the fully open valve with a 1 psi pressure drop across it.
A valve with a Cv of 2 passes 2 GPM of water at that 1 psi drop; a Cv of 10 passes 10.
Short answer: Cv is a capacity number, not a pressure rating. At the same pressure drop, the higher Cv delivers more flow. And the figure that matters is the one at the opening the valve will actually run at.
Key takeaways
- Cv is defined at the fully open position: GPM of 60 °F water per 1 psi drop — for water, flow scales as Q = Cv × √ΔP, so doubling the pressure drop does not double the flow.
- Higher Cv means more flow capacity at the same pressure drop; two valves with the same end size and orifice can still carry different Cv values because internal geometry sets the number.
- Makers publish Cv per model and size, sometimes at partial openings for needle and characterized ball valves — those partial-opening values are not linear with stroke.
- Cv is a comparison and sizing number, not a pressure rating: it says nothing about whether the valve body holds your line pressure — that is the class rating, covered in ball valve ratings explained.
Which valve do I need?
The first question is not which Cv but which job, because Cv only means something once the family is settled. The same tube end size can carry very different capacity depending on what sits inside the body.
| What the line needs | Family that fits | What decides the pick |
|---|---|---|
| Open or closed only, full flow when open | Ball valve, full-bore path | It runs fully open, so the full-open Cv on the table is the working number |
| Fine control at small flow | Needle valve | It spends its life at partial stroke, so Cv at that opening decides, not the full-open ceiling |
| More capacity in the same envelope at the same drop | Ball valve over a needle of the same end size | The internal path, not the end size: a ball opens full bore, a needle throttles through a fine annulus |
A compact ball valve and a needle valve of identical tube end size can differ in Cv by an order of magnitude: the ball opens a full-bore path, the needle throttles through a fine annulus.
Same end size, same pressure class, completely different flow capacity — Cv is the number that says so. Choosing between them is the shutoff-versus-throttling trade covered in needle valve vs ball valve.
What does the Cv number actually mean?
The definition is a test condition, not a guess: fully open valve, water at 60 °F, 1 psi differential, measure the flow.
Because flow and pressure drop relate through a square root, a Cv of 4 passes 4 GPM at 1 psi but about 5.7 GPM at 2 psi — doubling the pressure drop does not double the flow.
For liquids other than water the specific gravity enters the calculation; gases need their own corrected formulas.
The practical reading for an instrument buyer is simpler: at the same supply pressure and the same allowed drop, the higher-Cv valve delivers more flow to the actuator, the analyzer or the downstream leg.
Cv is a comparison and sizing number, not a pressure rating. It says nothing about whether the body holds your line pressure — that is the class rating, covered in ball valve ratings explained.
How do I read a maker’s Cv table?
Orifice diameter and Cv move together but are not the same thing. A larger orifice generally means a higher Cv, yet seat geometry, stem and port shape mean the same nominal orifice can carry different Cv values between makers.
That is why a serious table reads model by model rather than giving one number per thread size, and why it prints Cv alongside port orifice for each size.
For needle valves and characterized balls the table carries Cv at several opening positions, because capacity versus travel is deliberately shaped and not a straight line.
Read it at the opening you will actually run:
| What you are buying | The opening it runs at | The number to read |
|---|---|---|
| Ball valve, isolation | Fully open | The full-open Cv, straight from the table |
| Needle valve, metering | Partial stroke | Cv at that opening, not the ceiling figure |
| Characterized ball, modulating | Between the listed positions | The intermediate values the maker lists, which are not linear with stroke |
A needle valve bought for fine metering spends its life at partial stroke, so its fully open Cv is a ceiling, not the working number. A ball valve doing isolation duty runs fully open, where the table value applies directly.
How do I size a valve from Cv?
- Step 1 — write the duty down. Medium, flow rate, allowed pressure drop and the opening position the valve will run at. A Cv picked without those four is a guess.
- Step 2 — put the flow on the drop you have. For water, Q = Cv × √ΔP: a Cv of 4 passes 4 GPM at 1 psi and about 5.7 GPM at 2 psi.
- Step 3 — get the maker’s number for the size you are considering, read at the opening from Step 1. Where the family lists partial-opening values, use those; a full-open figure is the ceiling.
- Step 4 — check the valve is not left throttling near closed. A Cv picked “for margin” leaves the valve near closed, where control is coarse and seats wear. Size for the operating point with sensible margin.
- Step 5 — check class separately. Confirm the body and joints hold the line pressure. Nothing in the Cv figure does that for you.
What goes wrong when Cv is misused?
The same mistakes repeat, and they arrive as a control problem, a wear problem, or a line that will not pass the flow it should.
| Symptom | Most likely cause | What to change |
|---|---|---|
| Valve throttles near closed, control coarse, seats wearing | The largest Cv picked “for margin” | Size Cv for the operating point, with sensible margin |
| Line rated on Cv rather than class | Cv read as a pressure rating | Keep class and Cv as separate datasheet columns, and check the class against line pressure |
| Two valves with the same Cv behave differently at part open | Capacity compared across valve types — a globe pattern against a ball | Compare Cv within a family; character at part open is a separate question |
| Fine metering setting will not hold | A full-open Cv used as the working number for a partial-stroke duty | Read the table at the opening the valve actually runs at |
For metering duty where flow character matters, the valve-family discussion in high-pressure needle valves covers what the bonnet and stem geometry change.
What goes on the RFQ?
State the flow duty with the valve request — medium, flow rate, allowed pressure drop and opening position — and we size and quote the right family. The size list travels with it, because Cv is quoted per model and size.
- Medium — water, another liquid or a gas. The calculation changes with it, and so does the answer.
- Flow rate at the operating point.
- Allowed pressure drop across the valve.
- The opening position the valve will run at.
- The size list, so Cv is quoted per model and size rather than per thread size.
- A line asking for Cv to be stated on the quotation, for the exact model and size.
One honest note about our own catalog: FerruleX quotes Cv per order rather than publishing a fixed table on every SKU page. Cv varies with exact port geometry and size within a family, and a per-order confirmation keeps the datasheet tied to the valve you actually receive.
Start from the ball valve category for shutoff candidates and needle valves for metering duty. Request a factory quote.
FAQ
What does Cv stand for on a valve? Cv is the valve flow coefficient: US gallons per minute of 60 °F water through the fully open valve at a 1 psi drop. A Cv of 5 passes 5 GPM at that test condition.
Is a higher Cv always better? No. Higher Cv means more capacity at the same pressure drop — better only if the line needs that flow. An oversized high-Cv valve throttles near closed and controls poorly, so size Cv for the operating point with margin.
What is the difference between Cv and orifice size? Orifice size is one driver of Cv; seat, stem and port shape also set it. Two valves with the same orifice can carry different Cv values, so makers publish measured Cv per model, not calculated from diameter.
Does Cv change as the valve opens? For throttling valves, yes. Needle and characterized ball valves carry Cv tables at several opening positions, because flow versus travel is shaped, not linear. A full-open Cv is a ceiling, not the working number.
Is Cv the same as the pressure rating? No. Cv measures flow capacity; the pressure rating (class, CWP) is the pressure the body and joints hold. They are independent datasheet columns — a high-Cv valve can be a low-pressure valve and vice versa.



