NPT Thread Chart (Printable)
Threads per inch and actual thread diameter for NPT sizes 1/16″ through 4″ per ASME B1.20.1. Covers the taper and the diameter only — engagement lengths and gauge dimensions belong in the standard itself.
NPT sizes, TPI and thread diameter
| NPT size | Threads per inch | Basic major dia at thread end (in) | Dia (mm) |
|---|---|---|---|
| 1/16 | 27 | 0.3125 | 7.94 |
| 1/8 | 27 | 0.405 | 10.29 |
| 1/4 | 18 | 0.540 | 13.72 |
| 3/8 | 18 | 0.675 | 17.15 |
| 1/2 | 14 | 0.840 | 21.34 |
| 3/4 | 14 | 1.050 | 26.67 |
| 1 | 11.5 | 1.315 | 33.40 |
| 1-1/4 | 11.5 | 1.660 | 42.16 |
| 1-1/2 | 11.5 | 1.900 | 48.26 |
| 2 | 11.5 | 2.375 | 60.33 |
| 2-1/2 | 8 | 2.875 | 73.03 |
| 3 | 8 | 3.500 | 88.90 |
| 3-1/2 | 8 | 4.000 | 101.60 |
| 4 | 8 | 4.500 | 114.30 |
How to use this chart
NPT is a tapered thread — 1 in 16 on diameter, a 3/4-inch diameter change per foot of length — and it seals on the thread flanks with sealant, not on a gasket. The nominal size is not the diameter: a 1/2 NPT thread measures 0.840 inch at the basic major diameter, matching its pipe's OD in sizes 1/8″ and up. Listed diameters are the basic values at the thread-end reference; manufactured threads carry tolerance and inspection happens at the gauge plane defined in ASME B1.20.1.
NPTF (dryseal) shares the taper and TPI pattern but controls crest and root truncation so the joint can seal metal-to-metal with less reliance on sealant — an NPTF part is not a substitute for NPT by default. From our guide: NPT vs G (BSP) threads. State thread standard and size per line on theRFQ.
Nominal vs actual diameter
The nominal size is a name inherited from pipe, not a measurement of the thread. In the sizes 1/8″ and up, the basic major diameter equals the pipe's actual OD — 1/2″ pipe is 0.840 in outside, so the 1/2 NPT row reads 0.840, three tenths past the name. And because the thread tapers, the reading moves with position: expect a slightly smaller diameter toward the small end, and treat a few thousandths of spread between two honest caliper readings as the taper confirming itself, not a defect.
How to measure an NPT thread
Close calipers across the thread crests on the first full thread at the big end — skip the chamfered and incomplete threads — then take a second reading about a quarter inch along. A taper that reads larger toward the fitting body is NPT; a constant reading is a straight (NPS) thread. Follow with a pitch gauge for the TPI and match the pair against the table above. The full bench procedure, including female threads and the tools, is inhow to measure NPT fittings.
TPI groups explained
The threads-per-inch column falls into clean bands, which makes a partial count enough to place a size: 27 TPI covers 1/16 and 1/8; 18 covers 1/4 and 3/8; 14 covers 1/2 and 3/4; 11.5 covers 1 through 2; and 8 TPI takes over from 2-1/2″ upward. Counting threads in a quarter inch and multiplying by four lands you in the right band even without a gauge — the diameter column then picks the exact row.
NPTF: the dryseal variant
NPTF (ASME B1.20.3) shares the taper and TPI pattern of NPT but controls crest and root truncation so the threads interfere at crest and root as well as flank — closing more of the spiral leak path and allowing assembly with less reliance on sealant. Makers commonly still recommend lubricant or sealant on NPTF, and an NPT part assembled into an NPTF part is not automatically a certified dryseal joint.
Sealing an NPT joint
The engagement allowances in ASME B1.20.1 work out to roughly three wrench turns past hand-tight for sizes 1/8″ through 2″, and about two turns above that — a positional rule, not a torque spec. Sealant goes on the male thread only, started about one thread from the end so the first thread or two stays bare and compound stays out of the flow path. The end-by-end rules live inpipe dope vs Teflon tape on compression fittings.
Related thread standards
Two neighbors account for most NPT mix-ups. NPS(National Pipe Straight) shares the 60° form and TPI but runs parallel — it never seals on the thread, only on a gasket or O-ring; the comparison is inNPT vs NPS threads.BSP uses a 55° Whitworth form, ties NPT at 14 TPI in the 1/2 and 3/4 sizes, and never interchanges despite it — the bench test and full comparison are inhow to identify NPT vs BSP threads.