
Stainless Steel Air-Source Ball Valve — Sizes & Specs
Air-Source Ball Valve: stainless steel ball valve for compressed-air headers and FRL feeds. FerruleX RFQ. Stocked sizes ship fast. Export RFQ only — no cart.
- Brand
- FerruleX
- Material
- SS316 / SS316L / SS304
- Ends
- Compression / weld / thread
- Duty
- Compressed-air branch isolation
- Pressure
- 930 psi / 6.4 MPa
- Stock5–7 days after confirmation
- Make to order15–25 days production
- Payment / termsT/T ~30% or L/C · FOB Shanghai / Ningbo
- OEMLogo and drawings accepted · price on RFQ
Description
Shop air runs at a fraction of 930 psi, so on a compressed-air branch the pressure rating is never the constraint. This valve is built for the branch duty: isolating a drop or a manifold leg for maintenance. What limits it is the seat and the temperature. The seat takes the cycling every time the branch is opened and closed, and the working ceiling around 70 °C applies even though most shop air carries no process heat. Specify it as an isolating valve at the air source, with ferrule compression ends and the group rating of 930 psi (6.4 MPa), in sizes 3–25 mm and 1/8"–1". Throttling an air branch on a ball seat shortens seat life; give that duty to a needle or throttle valve instead.
Ball valve for compressed-air branch isolation at the air source. The 930 psi (6.4 MPa) rating sits well above shop-air pressure, so the seat and the working ceiling around 70 °C are the figures to check, not the pressure. Ferrule compression ends, 316, 316L or 304 stainless, sizes 3–25 mm and 1/8–1 in, ambient temperature service.
- Media
- Compressed air; branch isolation at the air source.
- Constraint
- Pressure is never the constraint on a shop-air branch.
- Range
- 930 psi (6.4 MPa) group rating, sizes 3–25 mm and 1/8"–1".
- Limit
- The seat and the 70 °C working ceiling set the limits.
Specifications
| Specification | Value |
|---|---|
| Brand | FerruleX |
| Material | SS316 / SS316L / SS304 |
| Ends | Compression, weld or thread |
| Tube OD | 3–25 mm / 1/8"–1" |
| Duty | Compressed-air branch isolation |
| Pressure | 930 psi / 6.4 MPa at ambient |
| Temperature | Ambient; working ceiling around 70 °C |
Request Quote
Prices stay on the RFQ. Send size, material, quantity and destination — the factory replies with price, lead time and packing. Packing, payment and the usual quote questions are on thedelivery pageand the FAQ.
Questions about this part
Do I need the 930 psi rating for a shop-air branch?
No. Shop air sits well below that, so the 930 psi (6.4 MPa) group rating is not the constraint. On a branch the seat and the working ceiling around 70 °C set the real limits.
What does the 70 °C working ceiling rule out?
It rules out any hot air line or a drop routed beside steam tracing. The valve is ambient-temperature duty with the ceiling around 70 °C, so the air temperature at the take-off is the figure to check.
Can I regulate the flow with it?
It is an isolating valve, not a control valve. Every throttle on a ball seat wears the seat and shortens its life, so give flow control to a needle or throttle valve downstream.
Which thread form should I specify for a threaded end?
State the form with the order. A male thread of one form will not seal into a female of the other, and no amount of tape makes it interchangeable. Thread ends are available, but compression and weld ends avoid the question.
Should I vent the isolated side before opening?
Always. A closed branch holds air with no way out, so vent the downstream side to atmosphere before you turn the handle. Opening against trapped pressure can damage the seat and endanger the operator.
Can I mount it in any orientation?
With compression or weld ends the body sits where you set it, so fit it handle-up or on its side as the pipe run allows. On thread ends the body stops where the thread makes up, so check the handle clearance first.
Related products

High-Pressure Compression Ball Valve
High-Pressure Compression Ball Valve: HP stainless steel ball valve with double ferrules. FerruleX RFQ. Stocked sizes ship fast. Export RFQ only — no cart.
View details →
Hex-Body Compression Ball Valve — Types & Sizes
Hex-body stainless ball valve with compression ends, 1000 psi, standard or long lever. Wrench flats for dense rows. FerruleX factory RFQ.
View details →
Stainless Steel Investment Cast Ball Valve — Sizes
Investment cast ball valve, 250 psi, DN6–DN100 (1/8"–4"), threaded or reducing ends, 304/316/316L. Utility shutoff at larger sizes. FerruleX RFQ.
View details →
Valve Manifold
Stainless valve manifold for instrument isolation and distribution. FerruleX factory RFQ. Confirm ports and pressure class.
View details →