Skip to content

Need stainless steel fittings, valves or hose?

Dual-plate check valve with spring-loaded half-discs in a wafer body — FerruleX stainless

Dual-Plate Check Valve

Dual-Plate Check Valve: two spring-loaded half-discs in a compact wafer body. SS304/316 stainless. FerruleX factory RFQ — confirm line size and class.

Brand
FerruleX
Material
CF8 / CF8M stainless typical
Type
Dual-plate check valve
Ends
Wafer pattern, ASME Class 150 / 300 typical
Pressure
Class 150 / 300 typical; from 2 in class range

Request a factory quote

  • Stock5–7 days after confirmation
  • Make to order15–25 days production
  • Payment / termsT/T ~30% or L/C · FOB Shanghai / Ningbo
  • OEMLogo and drawings accepted · price on RFQ

Description

Face-to-face length is the reason the pattern exists: the two half-discs fold back against the flow around a central pin instead of swinging through an arc, so the housing stays shallow enough to clamp between flanges as a wafer. The springs bias both discs toward the seat, shortening travel and starting closure before a single disc would. Discs are stainless CF8 or CF8M, with metal or resilient seats, and the catalogued range starts at 2 inch. Name the flange facing, the medium and the seat on the RFQ; the alloy follows the line rather than the datasheet.

Orientation follows the pin. Both discs have to fall shut against the flow, so the pin sits horizontal, or the run goes vertical with flow upward. Clamp the wafer flat between parallel flange faces: the body takes its alignment from the joint, not from its own length. The seat follows the medium named on the RFQ.

Discs
Two half-discs pivot on a central pin and fold back with the flow rather than swinging through an arc.
Springs
The springs bias both discs toward the seat, so travel stays short and closure begins early.
Alloy
Discs in CF8 or CF8M stainless, fixed against the line size and the medium.
Seat
Metal or resilient, settled with the medium on the order.

Specifications

SpecificationValue
BrandFerruleX
MaterialCF8 / CF8M stainless typical
TypeDual-plate check valve
EndsWafer pattern, ASME Class 150 / 300 typical
PressureClass 150 / 300 typical; from 2 in class range

Request Quote

Prices stay on the RFQ. Send size, material, quantity and destination — the factory replies with price, lead time and packing. Packing, payment and the usual quote questions are on thedelivery pageand the FAQ.

Request a factory quote

Questions about this part

What cracking pressure does the valve need to open?

Springs hold both discs against the seat, so a small forward differential lifts them. The springs are light enough to open on low forward flow, which is why the pair suits lines that reverse easily. Name the service on the RFQ.

How much pressure drop does the valve add when it is open?

The half-discs fold back against the flow instead of sitting across the bore, so the open area stays close to the pipe section and the loss is small. Low loss at high flow is the reason for the pattern.

Can the valve be fitted in a vertical line?

Yes, with flow upward. The pin sits horizontal in a horizontal run, or the line runs vertical with flow rising through it. The discs have to fall shut against the flow, so a downward run is not accepted.

Which way does the flow arrow point?

The arrow is cast or marked on the body and points in the permitted flow direction, so the marked side faces downstream. Fit the wafer with the arrow matching the pipe flow and check it before the flanges are drawn up.

Metal or resilient seat?

A resilient seat gives tighter shut-off at low pressure and is the usual choice for liquids and gases. Metal seats suit higher temperature and abrasive service, where a small amount of reverse weep is tolerated.

Will the discs chatter or slam on flow reversal?

Short spring travel closes both discs before the reverse flow builds, so the pair seats early and quietly. Chatter on a low-flow line is best handled by checking the springs and the line velocity at the joint.

Related products