Skip to content

Need stainless steel fittings, valves or hose?

SS KF Flexible Vacuum Corrugated Hose — FerruleX stainless steel fittings

SS KF Flexible Vacuum Corrugated Hose

SS KF Flexible Vacuum Corrugated Hose: KF16–50 / ISO63–100 vacuum hose, SS304. FerruleX factory RFQ — stocked fast. Stocked sizes ship fast. OEM RFQ welcome.

Brand
FerruleX
Material
SS304
KF sizes
KF16 / 25 / 40 / 50
ISO sizes
ISO63 / 80 / 100
Type
Flexible vacuum corrugated hose

Request a factory quote

  • Stock5–7 days after confirmation
  • Make to order15–25 days production
  • Payment / termsT/T ~30% or L/C · FOB Shanghai / Ningbo
  • OEMLogo and drawings accepted · price on RFQ

Description

Two vacuum ports rarely sit square to each other, and a corrugated SS304 hose takes up that offset without a rigid spacer fighting the alignment. The corrugation supplies the bend and absorbs small axial movement, so the flange faces stay parallel. Ends are KF16, KF25, KF40 or KF50; larger bores are supplied on ISO63, ISO80 and ISO100 flanges. Quote both end sizes, the free length and the vacuum level; the assembly is made to that length rather than picked off a size list. Clamps and centring rings, if needed, are listed separately on the RFQ. Common KF sizes are held in stock, so short runs ship sooner than ISO builds.

The selection point is how the hose is fixed at each end: KF16 to KF50 on the small bores, ISO63 to ISO100 on the larger ones, all in 304 stainless. Free length and the movement the run must absorb are set at order rather than read from a table, so send port centres and the gap between them.

Ends
KF16 / 25 / 40 / 50 or ISO63 / 80 / 100 on each side.
Alloy
304 stainless steel for the corrugated hose.
Length
Made to the installed gap between the two ports.
Duty
Flexible vacuum link that takes offset and vibration.

Specifications

SpecificationValue
BrandFerruleX
MaterialSS304
KF sizesKF16 / 25 / 40 / 50
ISO sizesISO63 / 80 / 100
TypeFlexible vacuum corrugated hose

Request Quote

Prices stay on the RFQ. Send size, material, quantity and destination — the factory replies with price, lead time and packing. Packing, payment and the usual quote questions are on thedelivery pageand the FAQ.

Request a factory quote

Questions about this part

Which KF and ISO sizes are held, and what vacuum level do they suit?

KF16, KF25, KF40 and KF50 cover the small bores and ISO63, ISO80 and ISO100 the larger ones. Vacuum level is agreed against the real assembly at RFQ rather than quoted from a table.

How do I set the length and bend radius for an offset between ports?

The free length is made to the installed gap between the two flange faces, not chosen from a list. Route the run so the bend is spread over several convolutions rather than forced at one point.

Does the hose take axial, lateral and angular movement?

Yes, the corrugation absorbs small axial, lateral and angular movement, and it also damps vibration reaching the flange faces. State the movement the run must take at order so the length is set for it.

What causes kinking near the ferrules, and how is it avoided?

A short straight run at each ferrule is what keeps the first convolution from folding when the hose is pulled sideways. Support the hose close to the end fitting and avoid a tight bend straight off the ferrule.

Is this a braided hose, and what duty does an unbraided build suit?

This is a plain corrugated SS304 hose without braid, intended as a flexible vacuum link. Without the braid it is not the build for pressure service, so state the duty when the RFQ is raised.

What should I look for when inspecting a hose in service?

Check each convolution for a flattened or cracked wall and look for a hose that no longer holds vacuum at the joints. A hose that has lost its corrugation profile has taken more movement than it was set for.

Related products