Skip to content

Need stainless steel fittings, valves or hose?

Square Head Plug — FerruleX stainless steel fittings

Square Head Plug

Square Head Plug: high-drive stainless steel pipe fittings blank with square drive. FerruleX RFQ. Stocked sizes ship fast. Export RFQ only — no cart.

Brand
FerruleX
Material
SS304 / SS316
Type
Square head plug
Threads
NPT 1/8–1 in typical; G / metric options
Order mode
Factory RFQ

Request a factory quote

  • Stock5–7 days after confirmation
  • Make to order15–25 days production
  • Payment / termsT/T ~30% or L/C · FOB Shanghai / Ningbo
  • OEMLogo and drawings accepted · price on RFQ

Description

A square drive is chosen over an internal hex when the plug has to break loose later without damaging the port. An open-end or adjustable wrench grabs all four flats, so a seized stainless plug can be worked free where a socket key would round out. Sizes run M5 to M36 and 1/8 to 2 inch, in ZG(R), NPT, G or M threads, with SS304, SS316, SS316L, copper or aluminium alloy bodies. Liquid and gas service, working pressure around 3000 PSI, typically as a permanent or semi-permanent blank on hydraulic blocks and manifold ports. Threads are cut to the ordered standard and checked against the mating port drawing before despatch. The square head stands higher than a hex plug, so confirm guard and cover clearance on mobile equipment.

Four flats accept a wrench from any quarter turn, which helps where a plug sits close to a manifold wall. The head stands above the port face, so it can be gripped again after the fitting has been in service. Threads are ZG(R), NPT, G or M; the port standard is stated on the drawing.

Head
The square section takes a wrench on all four flats and stands above the port face.
Sizes
The series spans M5 to M36 and 1/8 to 2 inch.
Threads
ZG(R), NPT, G and M forms are cut to the ordered standard.
Pressure
Working pressure is around 3000 PSI in liquid or gas service.

Specifications

SpecificationValue
BrandFerruleX
MaterialSS304 / SS316
TypeSquare head plug
ThreadsNPT 1/8–1 in typical; G / metric options
Order modeFactory RFQ

Request Quote

Prices stay on the RFQ. Send size, material, quantity and destination — the factory replies with price, lead time and packing. Packing, payment and the usual quote questions are on thedelivery pageand the FAQ.

Request a factory quote

Questions about this part

Which thread forms can the square head plug be cut in?

NPT, ZG(R), G and M forms are available, so the plug is matched to the port standard rather than adapted. State the port standard with the order, since each form is cut to that drawing.

How does a tapered thread seal compared with a parallel thread?

A tapered thread such as NPT or ZG(R) seals on the thread flanks as it is driven in, while a parallel G or M thread seals on a face or gasket, so the two are not interchangeable in one port.

Does a parallel thread plug need a gasket or washer?

A parallel G or M plug relies on a sealing face rather than thread interference, so a bonded washer or gasket is normally required. Without it the joint may weep even when the plug is fully seated.

Can an NPT plug be fitted into a BSPT port?

No, NPT and BSPT are different thread forms with a different flank angle and pitch, and forcing one into the other damages both threads. Order the plug in the port standard shown on the drawing.

What is done to stop stainless threads galling?

Stainless threads can pick up and seize when driven dry, so a nickel-based anti-seize compound on the threads is standard practice. Keep the compound off the sealing face of a parallel plug.

When should a plug be chosen over a cap?

A plug is driven into the port thread and blanks it from inside, while a cap covers the outside of a fitting and protects the connection. This square head plug stands above the port face.

Related products