Skip to content

Need stainless steel fittings, valves or hose?

Swing check valve with hinged disc for low pressure drop process lines — FerruleX stainless

Swing Check Valve

Swing Check Valve: hinged disc, low pressure drop for process lines. SS304/316 stainless. FerruleX factory RFQ — confirm line size and class.

Brand
FerruleX
Material
CF8M (cast 316) typical
Type
Swing check valve
Ends
Flanged, ASME Class 150 / 300 typical
Pressure
Class 150 / 300 typical; small-bore scope

Request a factory quote

  • Stock5–7 days after confirmation
  • Make to order15–25 days production
  • Payment / termsT/T ~30% or L/C · FOB Shanghai / Ningbo
  • OEMLogo and drawings accepted · price on RFQ

Description

The disc hangs from a hinge pin above the bore. Flow lifts it clear, the bore opens to near full diameter, and nothing sits in the stream. On reversal the disc drops back onto the seat under its own weight. That geometry is why the type suits low-head runs where a spring element would take pressure the system cannot spare. Installation decides whether it works: level pipe, or vertical with flow upward and the pin horizontal, so gravity can close what gravity opened. Bodies are flanged stainless, CF8M cast 316 or SS304/SS316, from 1/2 inch small bore upward, metal or resilient seat. Line size, flange facing and seat are named on the RFQ.

Orientation decides whether a swing check seats cleanly. On a vertical run with flow downwards the disc hangs on its hinge and gravity works against closure, so the valve can sit off its seat. Horizontal in a level run, it behaves as intended. Sketch the pipe run in the RFQ; trim and seat follow the medium.

Disc
The hinged disc swings clear of the bore, so the open valve leaves the line nearly unobstructed.
Seat
Metal or resilient seat, picked against the medium and named on the order.
Mounting
Level pipe, or a vertical run with flow upward and the hinge pin horizontal.
Ends
Flanged stainless bodies, quoted to the line size and facing on the RFQ.

Specifications

SpecificationValue
BrandFerruleX
MaterialCF8M (cast 316) typical
TypeSwing check valve
EndsFlanged, ASME Class 150 / 300 typical
PressureClass 150 / 300 typical; small-bore scope

Request Quote

Prices stay on the RFQ. Send size, material, quantity and destination — the factory replies with price, lead time and packing. Packing, payment and the usual quote questions are on thedelivery pageand the FAQ.

Request a factory quote

Questions about this part

Which way does the flow arrow point?

The arrow on the body points in the permitted flow direction, and the disc must lift with that flow. Fit the body so the arrow reads the same way as the line flow; reversing it holds the disc shut.

Can the valve be fitted on a vertical run?

Only with flow upward and the hinge pin horizontal, so the disc falls back onto the seat under its own weight. A downward vertical run lets gravity work against closure, leaving the disc hanging off the seat.

How much pressure drop does the open valve add?

Little, because the disc swings clear of the bore and the open body is close to full diameter, with no spring element in the stream. The type is chosen for low-head runs for that reason.

Metal or soft seat, which should I order?

Metal suits hot or abrasive mediums and tolerates rougher service; a resilient seat closes tighter on clean fluid at moderate temperature. Name the medium and the seat follows on the order.

Will it hold tight against reverse flow?

A resilient seat gives the closer shut-off on clean fluid; a metal seat relies on metal-to-metal contact and passes a small amount. State the acceptable leakage on the RFQ so the seat is chosen for it.

Does the disc slam or chatter in service?

Closure rests on gravity and on the reverse flow behind it, so a fast reversal can land the disc hard, and a flow near the lift point lets it chatter on the seat. Mention either case on the RFQ.

Related products