
Stainless Steel Weld-End Needle Valve — Sizes
Weld-End Needle Valve: stainless steel needle valve with weld prep for permanent metering. FerruleX RFQ. Stocked sizes ship fast. Export RFQ only — no cart.
- Brand
- FerruleX
- Material
- SS304 / SS316 / SS316L
- Ends
- Weld
- Pattern
- Straight or angle
- Pressure
- 2000 psi / 14 MPa
- Stock5–7 days after confirmation
- Make to order15–25 days production
- Payment / termsT/T ~30% or L/C · FOB Shanghai / Ningbo
- OEMLogo and drawings accepted · price on RFQ
Description
A weld end commits the valve to the line. Once the joint is closed there is no ferrule to undo and no thread to back out, so the only way to take the body off is to cut the tube and weld again. That is the right trade where a demountable joint is not allowed, or where vibration would work a compression nut loose. Bodies come in 304, 316 and 316L, from 3 mm to 16 mm tube and 1/8 to 1/2 in, with M10 to M24 threads where the run changes over to a threaded port. Rating is 2000 psi / 14 MPa nominal. Straight and angle patterns, panel mounting available. Settle the weld procedure before the valve arrives: heat reaches the seat faster than the body sheds it.
Service means cutting the line: no ferrule to release, no union nut to back off. Treat the valve as a permanent item and put isolation either side before you commit. Purge the bore and keep heat off the seat while welding, because a distorted seat will not meter cleanly afterwards.
- Joint
- The welded connection is permanent; removing the body means cutting the tube.
- Rating
- 2000 psi / 14 MPa nominal across the welded series.
- Patterns
- Straight and angle bodies, with panel mounting available.
- Seat care
- Purge the bore and sink heat away from the body while welding.
Specifications
| Specification | Value |
|---|---|
| Brand | FerruleX |
| Material | SS304 / SS316 / SS316L |
| Ends | Weld |
| Tube OD | 3–16 mm / 1/8"–1/2" |
| Threads | M10–M24 where a port is threaded |
| Pressure | 2000 psi / 14 MPa |
| Patterns | Straight or angle, panel mount available |
Request Quote
Prices stay on the RFQ. Send size, material, quantity and destination — the factory replies with price, lead time and packing. Packing, payment and the usual quote questions are on thedelivery pageand the FAQ.
Questions about this part
Is this valve for metering or for isolation?
Metering, primarily. The tapered needle gives fine control over flow, but it is not a bubble-tight isolation device in every position. Shut it fully for positive closure and use a separate valve for on-off duty.
Straight or angle body: which one suits a weld-end installation?
Straight bodies drop into a run with both welds on the same axis, so the tube stays aligned. Angle bodies save a bend where the line turns. Choose the pattern that removes a fitting, not the pattern that looks shorter.
Integral bonnet or union bonnet on this valve?
Welded lines usually take the integral bonnet, because fewer joints means fewer places for a leak to start. A union bonnet opens for packing or stem service without cutting the tube, which the welded body cannot do.
How is the packing adjusted, and how often?
The gland nut compresses the packing around the stem. Snug it only until weeping stops; over-tightening loads the stem and makes the valve stiff to turn. Recheck after the initial thermal cycle and at each service interval.
Does a small Cv mean poor metering resolution?
Not necessarily. Resolution comes from the needle taper and the stem travel from closed to open, not from the Cv figure alone. A low Cv with a long taper is easier to set than a large valve with a short travel.
Can this valve be panel mounted?
Yes, panel mounting is available on both patterns. The body is clamped through a panel cutout so the stem and handle sit on the operator side. Confirm the panel thickness at order, since it sets the clamping length.
Related products

Stainless Steel Straight Female Needle Valve — Types
Straight Female Needle Valve: stainless steel needle valve with female threads for manifolds. FerruleX RFQ. Stocked sizes ship fast. Export RFQ only — no cart.
View details →
Male-Female Straight Needle Valve, 316L, NPT
Male-Female Straight Needle Valve: stainless steel needle valve bridging dissimilar threads. FerruleX RFQ. Stocked sizes ship fast. Export RFQ only — no cart.
View details →
Angle Female Needle Valve
Angle Female Needle Valve: 90° stainless steel needle valve with female threads. FerruleX RFQ. Stocked sizes ship fast. Export RFQ only — no cart.
View details →
High-Pressure Female Globe Valve — Types & Sizes
High-Pressure Female Globe Valve: HP stainless throttling valve, female thread. SS316 preferred. FerruleX RFQ. Stocked sizes ship fast. Fast stock shipping.
View details →