Skip to content

Need stainless steel fittings, valves or hose?

Push-In Quick-Screw Fittings — FerruleX stainless steel fittings

Push-In Quick-Screw Fittings — Types & Sizes

Push-In Quick-Screw Fittings: stainless steel tube fittings, OD 4–12 mm / 1/8–1/2 in, pneumatic class 10–16 bar. SS304/316. FerruleX RFQ. Series and pressure class confirmed per order.

Brand
FerruleX
Material
SS304 / SS316 / SS316L
Tube OD
4–16 mm / 1/8"–1/2"
Pressure
Pneumatic class; 10–16 bar (145–230 psi) typical
Type
Push-in quick-screw

Request a factory quote

  • Stock5–7 days after confirmation
  • Make to order15–25 days production
  • Payment / termsT/T ~30% or L/C · FOB Shanghai / Ningbo
  • OEMLogo and drawings accepted · price on RFQ

Description

One cap nut, one body, one tube: back the nut off, push the tube over the body until it covers it completely, then turn the nut down. Six body patterns share that sequence: straight, female, straight union, elbow, tee and bulkhead. Tube ends run from Φ4 to Φ16 mm and 1/8" to 1/2", and the threaded patterns take ZG(R), NPT, G or M from M5 to M24. Bodies are SS304, SS316 or SS316L, listed for liquid and gas. A tube that stops short of full coverage is the fault the notes flag, so the wrap is checked before the nut goes down.

All six patterns in this series share the same nut-and-body logic, so a panel can be built from one size family. Tube 4–16 mm and 1/8"–1/2", threaded patterns in ZG(R), NPT, G or M from M5 to M24, machined in SS304, SS316 or SS316L, for liquid and gas duty.

Sequence
Back the nut off, push the tube over the body until it covers it completely, then turn the nut down.
Patterns
Straight, female, straight union, elbow, tee and bulkhead bodies share one cap-nut principle.
Sizes
Tube ends run from Φ4 to Φ16 mm and 1/8" to 1/2".
Threads
Threaded patterns are listed with ZG(R), NPT, G or M threads from M5 to M24.

Specifications

SpecificationValue
BrandFerruleX
MaterialSS304 / SS316 / SS316L
Tube OD4–16 mm / 1/8"–1/2"
PressurePneumatic class; 10–16 bar (145–230 psi) typical
TypePush-in quick-screw

Request Quote

Prices stay on the RFQ. Send size, material, quantity and destination — the factory replies with price, lead time and packing. Packing, payment and the usual quote questions are on thedelivery pageand the FAQ.

Request a factory quote

Questions about this part

Which tube materials can these push-in bodies take?

The joint is metal to metal, so the tube has to stay round under the cap nut. Stainless tube suits the SS304, SS316 and SS316L bodies directly; soft or thin-wall tube deforms and the joint is lost.

How does the pressure rating change with tube size?

The series is listed as a pneumatic class of 10 to 16 bar typical. The figure is confirmed per order against the chosen tube end and thread size, so the rating follows the configuration rather than a single headline number.

Can the fitting and the tube end be reused after dismantling?

Yes, where the parts are undamaged. The body and nut go back together, and a tube end that is still round and unscored can be reinserted and locked by the same sequence, provided it covers the body completely.

Do the tapered threads need a sealant?

Yes. ZG(R) threads are tapered and seal on the thread, so PTFE tape or a thread paste is used there. G and M threads are parallel and seal at the face, so the thread itself carries no sealant.

What panel thickness will a bulkhead body clamp?

The panel is clamped between the body shoulder and its lock nut, so panel thickness has to sit inside the threaded length of the body. Behind the panel, leave straight tube before the first bend.

Why does a tube pull out of the fitting?

Almost always because the tube stopped short of full coverage of the body, or the nut was not turned down after insertion. A tube that is oval, scored or heavily side loaded can also work loose.

Related products