Skip to content

Need stainless steel fittings, valves or hose?

Quick-Screw Straight Union — FerruleX stainless steel fittings

Stainless Steel Quick-Screw Straight Union — Types

Quick-Screw Straight Union: stainless steel tube fittings for equal tube-to-tube joins. FerruleX factory RFQ. Stocked sizes ship fast. Fast stock shipping.

Brand
FerruleX
Material
SS304 / SS316 / SS316L
Tube OD
4–16 mm / 1/8"–1/2"
Type
Quick-screw straight union
Pressure
Pneumatic class; 10–16 bar (145–230 psi) typical

Request a factory quote

  • Stock5–7 days after confirmation
  • Make to order15–25 days production
  • Payment / termsT/T ~30% or L/C · FOB Shanghai / Ningbo
  • OEMLogo and drawings accepted · price on RFQ

Description

Both ends of this union are the same quick-screw socket, so a stores crib holds one body for a whole hose run instead of a male and a female version. Make-up is three moves: nut off, hose pushed on until it fully covers the body, nut rotated down. Bodies come in 316, 316L or 304 stainless, with copper on request, for tube OD 4 to 16 mm, the same range as 1/8 in to 1/2 in tube. Port threads are cut in ZG(R), NPT, G or M. Duty is liquid or gas, typically air and water line in energy and environmental plant, automotive and shipbuilding, petrochemical, construction, food processing and pharmaceutical works. Order by tube OD and thread code.

Service is the reason to fit a screwed union at this point in the line: the nut comes off, the hose lifts clear and the body stays put. Both sockets take the same tube OD, with no reducing step. Bodies are 316, 316L or 304 stainless, and the port thread is cut to ZG(R), NPT, G or M.

Sockets
Both ends are cut for one tube OD, so no reducing step sits in the bore.
Grip
The hose is pushed on until it covers the body, then the nut is rotated down.
Alloys
316, 316L or 304 stainless, with copper on request.
Port thread
ZG(R), NPT, G or M form, cut as ordered.

Specifications

SpecificationValue
BrandFerruleX
MaterialSS304 / SS316 / SS316L
Tube OD4–16 mm / 1/8"–1/2"
TypeQuick-screw straight union
PressurePneumatic class; 10–16 bar (145–230 psi) typical

Request Quote

Prices stay on the RFQ. Send size, material, quantity and destination — the factory replies with price, lead time and packing. Packing, payment and the usual quote questions are on thedelivery pageand the FAQ.

Request a factory quote

Questions about this part

Can copper or plastic tube be used on this union?

The socket is cut for 4 to 16 mm or 1/8 in to 1/2 in tube OD, and copper takes the same grip as stainless. A soft-wall plastic tube deforms under the nut, so it is not a reliable choice.

Does the pressure rating change with tube size?

The union is rated pneumatic class, 10 to 16 bar, or 145 to 230 psi typical. Duty falls as tube OD grows, so confirm your working pressure when ordering.

Can the nut and the hose end be reused after a strip-down?

The body and nut are reused: the nut comes off, the hose lifts clear and the same parts go back on. The hose end is reusable only if it is trimmed square and pushed fully home again.

Is sealant needed on the port thread?

On ZG(R) and NPT tapered threads, yes, a thread sealant is normal practice. G and M threads are parallel and seal on their own face, so they take no tape or paste.

How does the joint behave under vibration or tube side load?

The nut is a screwed mechanical grip, so light vibration is held. A sustained side load on the tube levers against the socket, and that is the usual route to a weeping joint.

What causes a hose to pull out of the union?

The hose was not pushed fully onto the body before the nut went down, the tube end was cut at an angle, or the nut was left part-tight. Any of those leaves the grip short.

Related products