Skip to content

Need stainless steel fittings, valves or hose?

Quick-Screw Elbow Connector — FerruleX stainless steel fittings

Quick-Screw Elbow Connector

Quick-Screw Elbow Connector: 90° stainless steel tube fittings for tight cabinets. OD 4–6 mm. FerruleX RFQ. Stocked sizes ship fast. Export RFQ only — no cart.

Brand
FerruleX
Material
SS304 / SS316 / SS316L
Tube OD
4–6 mm / 1/8"–1/2"
Pattern
Elbow
Pressure
Pneumatic class; 10–16 bar (145–230 psi) typical

Request a factory quote

  • Stock5–7 days after confirmation
  • Make to order15–25 days production
  • Payment / termsT/T ~30% or L/C · FOB Shanghai / Ningbo
  • OEMLogo and drawings accepted · price on RFQ

Description

Where a port faces sideways in a tight cabinet, the elbow carries the turn in metal so the run clears adjacent hardware. Assembly follows the quick-screw sequence: cap off, hose pressed into the body until it covers the body completely, cap turned down. A hose that stops short of full coverage leaves the joint loose under the cap. FerruleX machines the pattern in SS304, SS316 and SS316L, with copper listed as an alternative. Hose side covers Φ4–Φ16 mm and 1/8"–1/2"; threads are ZG(R), NPT, G or M from M5 to M24. Rating for the quick-screw range is about 1000 psi, on liquid and gas service.

The elbow is a body plus a cap nut, and the corner belongs to the body. Press the hose over the body first, then bring the cap down; it is the cap that holds, not the bend. Bodies come in 316L, 316 or 304, with thread ends in ZG(R), NPT, G or M.

Corner
A body takes the angle, so the hose is not asked to hold it.
Hose side
Φ4–Φ16 mm and 1/8"–1/2", pressed over the body before the cap.
Threads
ZG(R), NPT, G or M, M5 to M24.
Service
Liquid and gas, about 1000 psi for this series.

Specifications

SpecificationValue
BrandFerruleX
MaterialSS304 / SS316 / SS316L
Tube OD4–6 mm / 1/8"–1/2"
PatternElbow
PressurePneumatic class; 10–16 bar (145–230 psi) typical

Request Quote

Prices stay on the RFQ. Send size, material, quantity and destination — the factory replies with price, lead time and packing. Packing, payment and the usual quote questions are on thedelivery pageand the FAQ.

Request a factory quote

Questions about this part

Which tube materials suit this elbow?

The cap compresses the tube wall, so it suits flexible tubing rather than rigid pipe; the metal body is SS304, SS316 or SS316L. State the tube material and bore on the RFQ so the body barb matches.

Does the pressure rating change with tube size?

This elbow carries the series figure of about 1000 psi, with 10–16 bar (145–230 psi) typical quoted in the table for the pneumatic class. The tube, not the body, is normally the weaker member, so confirm its own rating.

Can the connection be taken apart and remade?

The body and cap are reusable and the tube end is the part to renew. Cut the tube back a short length and press it fully over the body again before the cap is turned.

Is thread sealant needed on the port end?

A tapered ZG(R) or NPT end needs a thread sealant or PTFE tape to seal; the parallel G and M ends are intended to seal at the face. Keep sealant clear of the bore.

Will vibration or side load on the tube work the joint loose?

The cap is a threaded nut, so sustained side load at the bend can work it loose; support the run close to the elbow. Where vibration is continuous, check the cap at service intervals.

What causes the tube to pull out of the body?

Almost always incomplete coverage: the tube must be pressed down until the body is fully covered before the cap is turned. A tube that stops short leaves the joint loose, and side load finishes it.

Related products