Skip to content

Need stainless steel fittings, valves or hose?

Quick-Screw Bulkhead Connector — FerruleX stainless steel fittings

Quick-Screw Bulkhead Connector — Types & Sizes

Quick-Screw Bulkhead Connector: panel-pass stainless steel tube fittings, OD 4–16 mm. FerruleX factory RFQ. Stocked sizes ship fast. Export RFQ only — no cart.

Brand
FerruleX
Material
SS304 / SS316 / SS316L
Tube OD
4–16 mm / 1/8"–1/2"
Type
Quick-screw bulkhead
Pressure
Pneumatic class; 10–16 bar (145–230 psi) typical

Request a factory quote

  • Stock5–7 days after confirmation
  • Make to order15–25 days production
  • Payment / termsT/T ~30% or L/C · FOB Shanghai / Ningbo
  • OEMLogo and drawings accepted · price on RFQ

Description

Panel penetrations on stainless tube runs are where a skid starts weeping. This body clamps through the wall, so tubing crosses into the enclosure without a welded stub. Bodies come in SS304, SS316 and SS316L, in Φ4–Φ16 mm and 1/8–1/2 in, quick-screw on the tube side, for liquid or gas at around 1000 psi working pressure. It suits energy and environmental plant, automotive and shipbuilding lines, petrochemical work, construction, food processing and pharmaceutical skids. Send wall thickness and tube OD on the RFQ and the port size is quoted to suit. Before tightening, check the panel face is flat: a cocked body will not seal however hard the nut is drawn.

The tube side is quick-screw; the panel side carries a locknut that clamps the body against the wall. That make-up is not the compression type, where ferrules seal the tube, so the two series do not interchange. Wall thickness, tube OD and whether both faces take the same OD all go on the RFQ.

Tube side
Quick-screw port takes Φ4–Φ16 mm and 1/8–1/2 in tube.
Panel side
A locknut clamps the body through the enclosure wall.
Alloys
SS304, SS316 and SS316L bodies, with copper offered in the same series.
Pressure
Around 1000 psi working pressure in liquid or gas service.

Specifications

SpecificationValue
BrandFerruleX
MaterialSS304 / SS316 / SS316L
Tube OD4–16 mm / 1/8"–1/2"
TypeQuick-screw bulkhead
PressurePneumatic class; 10–16 bar (145–230 psi) typical

Request Quote

Prices stay on the RFQ. Send size, material, quantity and destination — the factory replies with price, lead time and packing. Packing, payment and the usual quote questions are on thedelivery pageand the FAQ.

Request a factory quote

Questions about this part

Which tube materials does the quick-screw port accept?

The port takes stainless tube in the same SS304, SS316 or SS316L family as the body, and copper is offered in the same series. State the tube grade on the RFQ.

How is the working pressure affected by tube size?

The rating follows the tube wall and the nut make-up, not the body alone, so a figure only holds for the tube actually fitted. Give tube OD and wall thickness on the RFQ.

How does it mount through a panel, and what wall thickness suits?

The body passes through the wall and a locknut draws it against the panel face. Wall thickness and the tube OD on each side go on the RFQ, and the face must be flat or the body will cock.

How much clearance is needed behind the panel?

Leave room behind the wall to swing the nut and to take the tube bend without levering the joint. Check that swing before the hole is drilled.

Can the fitting and the tube end be reused after a remake?

The nut backs off and the body can be re-made, but the tube end has to be clean, unscored and cut square before it goes back in. Re-check the joint at working pressure.

What causes a tube to pull out of the connector?

Under-tightened nuts, tube ends cut out of square and side load on the run are the usual causes. Support the tube near the panel and check the cut before the joint is blamed.

Related products