Skip to content

Need stainless steel fittings, valves or hose?

Quick-Screw Straight Connector — FerruleX stainless steel fittings

Quick-Screw Straight Connector — Sizes & Specs

Quick-Screw Straight Connector: stainless steel tube fittings, tube to thread, pneumatic class 10–16 bar. FerruleX factory RFQ. Pressure class confirmed per order.

Brand
FerruleX
Material
SS304 / SS316 / SS316L
Tube OD
4–16 mm / 1/8"–1/2"
Type
Quick-screw straight
Pressure
Pneumatic class; 10–16 bar (145–230 psi) typical

Request a factory quote

  • Stock5–7 days after confirmation
  • Make to order15–25 days production
  • Payment / termsT/T ~30% or L/C · FOB Shanghai / Ningbo
  • OEMLogo and drawings accepted · price on RFQ

Description

A quick-screw body holds the hose with a cap nut turned down onto the fitting, after the hose has been pressed over the body until it covers it completely. FerruleX lists the straight pattern in SS304, SS316 and SS316L, tube 4–16 mm and 1/8"–1/2", against ZG(R), NPT, G or M threads from M5 to M24. One end takes hose, the other is male or female thread for plant air and water lines. The manual gives working pressure for this series as about 1000 psi, with liquid and gas as the stated media.

Fitting sequence is fixed: back the cap nut off, press the hose in until it covers the body fully, then tighten. Sizes cover tube 4–16 mm and 1/8"–1/2" with ZG(R), NPT, G or M threads from M5 to M24, in SS304, SS316 or SS316L. About 1000 psi. Liquid and gas.

Body
Straight body, hose end to thread end.
Cap nut
Turned down after the hose is pressed fully over the body.
Threads
ZG(R), NPT, G or M, from M5 to M24.
Rating
About 1000 psi for this series, liquid and gas.

Specifications

SpecificationValue
BrandFerruleX
MaterialSS304 / SS316 / SS316L
Tube OD4–16 mm / 1/8"–1/2"
TypeQuick-screw straight
PressurePneumatic class; 10–16 bar (145–230 psi) typical

Request Quote

Prices stay on the RFQ. Send size, material, quantity and destination — the factory replies with price, lead time and packing. Packing, payment and the usual quote questions are on thedelivery pageand the FAQ.

Request a factory quote

Questions about this part

Which hose materials can be used with this body?

The body is SS304, SS316 or SS316L, sized for hose of 4 mm to 16 mm and 1/8 to 1/2 in OD. The hose compound itself must suit the medium, liquid or gas, and the working temperature, so state it on the RFQ.

Does the pressure rating change with hose size?

The manual gives one figure for the series, about 1000 psi, and the spec table lists 10–16 bar typical for the pneumatic class. Neither is split by hose size, so state the line size on the RFQ.

Can the fitting and the hose end be reused after dismantling?

The cap nut can be backed off and retightened on the same body. A hose that has already been compressed is best cut back to clean, round section before it is pressed on again.

Should thread sealant be used on the thread end?

ZG(R) and NPT are tapered and seal on the thread flanks, so use a thread sealant suited to the medium. G and M are parallel and rely on a sealing washer at the face.

How much side load can the hose take at the fitting?

The cap nut holds the hose by compression only, so the joint is not a strain relief. Support the hose close to the body and keep vibration and side pull off the connection.

What causes a hose to pull out of the body?

In practice it is a hose that stopped short of covering the body completely, or a cap nut left only part tight. The hose must cover the body before the cap is turned down.

Related products