Skip to content

Need stainless steel fittings, valves or hose?

Quick-Screw Female Connector — FerruleX stainless steel fittings

Stainless Steel Quick-Screw Female Connector — Sizes

Quick-Screw Female Connector: stainless steel tube fittings to female NPT/G ports. SS304/316. FerruleX RFQ. Stocked sizes ship fast. Export RFQ only — no cart.

Brand
FerruleX
Material
SS304 / SS316 / SS316L
Tube OD
4–6 mm / 1/8"–1/2"
Female threads
NPT / G / Metric
Pressure
Pneumatic class; 10–16 bar (145–230 psi) typical

Request a factory quote

  • Stock5–7 days after confirmation
  • Make to order15–25 days production
  • Payment / termsT/T ~30% or L/C · FOB Shanghai / Ningbo
  • OEMLogo and drawings accepted · price on RFQ

Description

Two ends define the part: a quick-screw nut takes the tube, the body carries an internal thread that screws straight onto a port, so no nipple sits in between. Bodies are 304, 316 or 316L stainless; tube side covers Φ4–Φ16 mm and 1/8"–1/2" in, thread side ZG(R), NPT, G or M from M5 to M24. Media are liquid and gas, with a listed working pressure of about 1000 psi. Feed the tube into the loose nut, press it down until it seats over the body, then tighten the nut. Thread sealant belongs on the male mating thread, never on the tube bore.

Where the port is already threaded, the install is a single joint: press the tube in, run the nut down, and the body screws home. It appears across petrochemical, food processing, pharmaceutical, shipbuilding and construction plant, on liquid and gas. Keep sealant off the tube bore.

Tube end
Quick-screw nut takes Φ4–Φ16 mm and 1/8"–1/2" in tube.
Port end
Internal thread in ZG(R), NPT, G or M, from M5 to M24.
Grades
Bodies in 304, 316 or 316L stainless.
Duty
Liquid and gas media, from petrochemical to pharmaceutical lines.

Specifications

SpecificationValue
BrandFerruleX
MaterialSS304 / SS316 / SS316L
Tube OD4–6 mm / 1/8"–1/2"
Female threadsNPT / G / Metric
PressurePneumatic class; 10–16 bar (145–230 psi) typical

Request Quote

Prices stay on the RFQ. Send size, material, quantity and destination — the factory replies with price, lead time and packing. Packing, payment and the usual quote questions are on thedelivery pageand the FAQ.

Request a factory quote

Questions about this part

Which tube materials can be used with this connector?

Built for stainless tube. The body is 304, 316 or 316L, so keep the tube in the same family and the joint runs one wetted alloy throughout.

Does the pressure rating change with tube size?

Yes. The body is listed in the pneumatic class, and the larger the tube bore the lower the safe working pressure, so size the joint against your actual line pressure, not the catalogue maximum.

Can the fitting and the tube end be reused after dismantling?

The body and nut can be unscrewed and remade. The tube end is the part that suffers: if the nut has marked or scored it, cut the tube back square before refitting rather than reusing the damaged section.

Should sealant go on the female thread or the mating male thread?

Sealant goes on the male thread that enters the body, sparingly, and never inside the tube bore or on the tube seat, where it would be pushed into the flow path.

Will vibration or side load on the tube loosen the joint?

The nut is a threaded joint, so sustained vibration can back it off. Support the tube near the fitting and keep side load off the body; where movement is constant, check the nut at service intervals.

What causes a tube to pull out of this connector?

Almost always an incomplete make-up: the nut was run down before the tube was pressed fully home, or the tube was cut short of square. Neither the nut torque nor the thread holds a tube that never seated.

Related products