
Quick-Screw Tee Connector
Quick-Screw Tee Connector: three-way stainless steel push-to-connect fitting for air circuits, 1000 psi. FerruleX factory RFQ.
- Brand
- FerruleX
- Material
- SS304 / SS316 / SS316L
- Ends
- Push-to-connect, three legs
- Tube OD
- 3–25 mm / 1/8"–1"
- Pressure
- 1000 psi
- Stock5–7 days after confirmation
- Make to order15–25 days production
- Payment / termsT/T ~30% or L/C · FOB Shanghai / Ningbo
- OEMLogo and drawings accepted · price on RFQ
Description
A quick-screw tee splits one tube run into two without tools: push the tube in, the grip bites, the seal seats. On a pneumatic panel that is the difference between a branch added in a minute and a branch that needs a fitting change. The three legs take the same tube OD unless the body is built as a reducing tee, so state run and branch sizes separately on the RFQ. It is a push-to-connect part, which means the tube does the sealing — PU or nylon for air and light fluid, never metal tube. The group is rated 1000 psi, well above shop-air pressure, and bodies come in 304, 316 or 316L for washdown areas where plastic fittings crack. Panel builders usually cap an unused leg rather than leave it open through commissioning.
Three push-to-connect legs, one branch run: the tee splits air or light-fluid tubing without tools. State run OD and branch OD separately, because a reducing body is a different part. 1000 psi group rating, 304, 316 or 316L body, and PU or nylon tube — never metal tube in a push-to-connect leg.
- Branch
- Splits one run into two; run and branch sizes stated separately.
- Joining
- Push-to-connect: the tube is gripped and sealed without tools.
- Tube
- PU or nylon for air and light fluid; metal tube defeats the grip.
- Rating
- 1000 psi group rating, 304, 316 or 316L body.
Specifications
| Specification | Value |
|---|---|
| Brand | FerruleX |
| Material | SS304 / SS316 / SS316L |
| Ends | Push-to-connect, three legs |
| Tube OD | 3–25 mm / 1/8"–1" |
| Tube type | PU or nylon |
| Pressure | 1000 psi |
Request Quote
Prices stay on the RFQ. Send size, material, quantity and destination — the factory replies with price, lead time and packing. Packing, payment and the usual quote questions are on thedelivery pageand the FAQ.
Questions about this part
Which tubes can I run in this tee?
PU or nylon only, for air and light fluid. The grip and the seal both rely on the tube wall, so metal tube will not hold in a push-to-connect leg and should not be specified here.
Does the 1000 psi rating hold at every tube size?
It is a group rating for the fitting family, not a per-size promise. A thin wall tube near the top of the 3–25 mm range gives up margin first, so state tube OD and wall on the RFQ.
Can I reuse the tube end after pulling it out?
The fitting body and the grip can be reused, but the tube end usually cannot. Pulling the tube scores the surface where the seal sits, so cut a clean square end before you push it back in.
Which media can the seal handle?
The seal is wetted, so the medium decides the compound. Air and light fluid are the intended service here; for anything else state the medium on the RFQ rather than assuming the standard seal covers it.
Will vibration or a side load on the tube break the grip?
The grip holds the tube axially, not as a structural support. Support long tube runs and keep side load off the tee, because a sustained lever at the leg is what works a push-to-connect joint loose.
Why does a tube pull out of the fitting?
Usually a tube that was never pushed fully home, a scored or oval end, or a wall too soft for the grip. Cut the end square, push until it seats, then pull back gently to confirm the grip.
Related products

Quick-Screw Bulkhead Connector — Types & Sizes
Quick-Screw Bulkhead Connector: panel-pass stainless steel tube fittings, OD 4–16 mm. FerruleX factory RFQ. Stocked sizes ship fast. Export RFQ only — no cart.
View details →
Compression / Quick-Screw Straight & Bulkhead Connectors
Compression / Quick-Screw Straight & Bulkhead: hybrid stainless fittings for mixed tube styles. FerruleX RFQ. Stocked sizes ship fast. Fast stock shipping.
View details →
Push-In Quick-Screw Fittings — Types & Sizes
Push-In Quick-Screw Fittings: stainless steel tube fittings, OD 4–12 mm / 1/8–1/2 in, pneumatic class 10–16 bar. SS304/316. FerruleX RFQ. Series and pressure class confirmed per order.
View details →
Quick-Screw Straight Connector — Sizes & Specs
Quick-Screw Straight Connector: stainless steel tube fittings, tube to thread, pneumatic class 10–16 bar. FerruleX factory RFQ. Pressure class confirmed per order.
View details →