Skip to content

Need stainless steel fittings, valves or hose?

Push-to-Connect Bulkhead Fitting — FerruleX stainless steel fittings

Push-to-Connect Bulkhead Fitting — Types & Sizes

Push-to-Connect Bulkhead Fitting: panel-pass stainless push-in fitting. SS304/316. FerruleX factory RFQ. Stocked sizes ship fast. Export RFQ only — no cart.

Brand
FerruleX
Material
SS304 / SS316
Type
Push-to-connect bulkhead
Mount
Panel bulkhead
Order mode
Factory RFQ

Request a factory quote

  • Stock5–7 days after confirmation
  • Make to order15–25 days production
  • Payment / termsT/T ~30% or L/C · FOB Shanghai / Ningbo
  • OEMLogo and drawings accepted · price on RFQ

Description

One body, two push-in ports, one locknut: the bulkhead crosses a cabinet wall and keeps the tube run in one piece. Bodies are SS304, SS316 or SS316L, with copper listed in the same series, and take Φ3–Φ25 mm or 1/8–1 inch tube, which is 3.175–25.4 mm. Threaded ends are cut to ZG(R), NPT, G or M, M10–M24 within that range. Liquid or gas service, -10 to 300 °C unfrozen. Drill the hole to the thread, check the wall face is flat, draw the nut before the tube goes in. These are push-in ports, so the tube must match the series; panel thickness and tube OD belong on the RFQ. Pressure duty moves with tube and wall thickness, so it is fixed per configuration.

The panel hole is a thread match, not a clearance hole: the body draws up on its locknut until the face sits flat. Tube then enters each push-in port and the grab ring holds it, so a run is broken at the cabinet without touching the wall joint. Send OD, thread, wall thickness.

Tube ports
Push-in ports take Φ3–Φ25 mm or 1/8–1 inch tube.
Panel side
The body draws up on a locknut against the wall face.
Threads
Ends are cut to ZG(R), NPT, G or M, M10–M24 in the range.
Alloys
SS304, SS316 and SS316L, with copper listed in the same series.

Specifications

SpecificationValue
BrandFerruleX
MaterialSS304 / SS316
TypePush-to-connect bulkhead
MountPanel bulkhead
Order modeFactory RFQ

Request Quote

Prices stay on the RFQ. Send size, material, quantity and destination — the factory replies with price, lead time and packing. Packing, payment and the usual quote questions are on thedelivery pageand the FAQ.

Request a factory quote

Questions about this part

Which tube materials can the push-in ports take?

Bodies are offered in SS304, SS316 and SS316L, with copper listed in the same series, so the port material follows the tube run. State the tube alloy and the medium on the RFQ before the body is cut.

What pressure will the bulkhead hold?

Pressure duty moves with tube and wall thickness, so it is fixed per configuration and not stated as one figure. Give the tube OD, the wall and the working pressure together on the RFQ.

What does the panel need for mounting?

Drill the hole to the thread, not to clearance, and check that the wall face is flat so the locknut draws up square. Panel thickness and tube OD belong on the RFQ.

Should sealant go on the threads?

The panel side is sealed by the locknut drawing up on the wall face, so no thread tape is needed there. On a threaded port end, use a sealing compound that suits the medium and apply it to the male thread only.

What temperature range suits it?

Liquid or gas service runs from -10 to 300 °C unfrozen. Stay inside that band, keep the medium within what the body alloy handles, and confirm both on the RFQ.

Can the fitting be reused after a tube is removed?

Yes, if the tube is drawn fully and the grab ring is not deformed on removal. Reuse the body and locknut, but inspect the port seal each time and renew it if the tube has been pulled out repeatedly.

Related products