Skip to content

Need stainless steel fittings, valves or hose?

Push-to-Connect Straight Fitting — FerruleX stainless steel fittings

Push-to-Connect Straight Fitting

Push-to-Connect Straight Fitting: stainless push-in tube fitting for air/water. SS304/316. FerruleX RFQ. Stocked sizes ship fast. Export RFQ only — no cart.

Brand
FerruleX
Material
SS304 / SS316
Type
Push-to-connect straight
Media
Air / water (confirm)
Order mode
Factory RFQ

Request a factory quote

  • Stock5–7 days after confirmation
  • Make to order15–25 days production
  • Payment / termsT/T ~30% or L/C · FOB Shanghai / Ningbo
  • OEMLogo and drawings accepted · price on RFQ

Description

A straight push-in body carries two different joints on one axis: a collet end for tube, and a threaded end in ZG(R), NPT, G or M. Tube runs Φ3 to Φ25 mm, or 1/8 to 1 inch; threads run M10 to M24. Materials offered are SS304, SS316, SS316L and copper, for liquid or gas service. Because both ends are push or thread, tube must arrive round and burr-free — a collet grips the OD and will not straighten a bent end. Working pressure is listed at about 3000 psi; the figure covers the body and thread, so the tube wall still governs the line.

Two figures fix the part: tube OD and thread size. Give both, with the thread family — ZG(R), NPT, G or M — and the tube end stays Φ3 to Φ25 mm or 1/8 to 1 inch. The body is listed for liquid and gas across energy, marine, petrochemical, construction, food and pharmaceutical work.

Tube end
Collet end takes tube from Φ3 to Φ25 mm or 1/8 to 1 inch.
Threads
ZG(R), NPT, G or M, with the metric span running M10 to M24.
Metals
SS304, SS316, SS316L and copper are the four listed options.
Service
Liquid and gas, across energy, marine, petrochemical, construction, food and pharmaceutical plant.

Specifications

SpecificationValue
BrandFerruleX
MaterialSS304 / SS316
TypePush-to-connect straight
MediaAir / water (confirm)
Order modeFactory RFQ

Request Quote

Prices stay on the RFQ. Send size, material, quantity and destination — the factory replies with price, lead time and packing. Packing, payment and the usual quote questions are on thedelivery pageand the FAQ.

Request a factory quote

Questions about this part

What tube materials can the collet end take?

The page lists liquid and gas service rather than a tube family, so give the tube material and wall on the RFQ. The collet grips the outside diameter, and that surface carries the seal.

Does the 3000 psi rating hold at every tube size?

The figure covers the body and the thread, not the tube. It is listed at about 3000 psi across the Φ3 to Φ25 mm and 1/8 to 1 inch ends, but the tube wall governs the line.

Can a push-to-connect joint be opened and remade?

Yes. Pressing the sleeve releases the collet and the tube withdraws, and the joint can then be remade. Check the tube outside diameter for scoring first, since a scored surface will not seal again.

Is sealant needed on the threaded end?

Sealant goes on the male thread only. Keep it off the collet end, because tape fragments and paste in the bore can hold the collet open and stop the tube from seating.

What makes a tube pull out of the collet?

A bent or burred tube end is the usual cause, because the collet grips the outside diameter and cannot straighten it. Side load on the run, or a tube not pushed fully home, does the same.

How much side load and vibration can the straight body take?

The collet is a grip, not a support. Keep the run clipped close to the body so vibration and side load do not work the tube loose, and do not use the fitting to carry the weight of the line.

Related products