Metric compression fittings live in a parallel world to the fractional-inch one: same mechanism, same bite, different numbers — and a hard lesson for anyone who assumes the two worlds nearly-meet.
The working core is 6, 8, 10, 12, 15, 18, 22 and 25 mm OD, carried on two thread families: metric fine per the ISO 261 ladder, and G. Buy by exact tube OD, wall and tail thread.
Close is not compatible. A 12 mm ferrule cannot seal 1/2 inch tubing — that 0.7 mm gap is what this walkthrough is about — and a transition fitting is the only correct bridge.
Key takeaways
- The common metric instrument range runs 6, 8, 10, 12, 15, 18, 22 and 25 mm OD — a working subset of maker catalogs that extend the series in both directions.
- Metric and inch fittings are not interchangeable at near-equal sizes: a 12 mm ferrule against 1/2 inch tube leaves roughly a 0.7 mm mismatch the seal cannot close.
- Two thread systems ride on metric fittings: metric fine threads per the ISO 261 ladder (M12×1.5 upward) and G threads on the same bodies.
- DIN 2353 / ISO 8434-1 is the metric-native standard: L series 6–42 mm, S series 6–38 mm, LL 4–12 mm — and its size ladder is why 15 and 22 mm exist at all.
- Write tube as OD × wall plus the tail thread standard, and the metric line quotes without a clarification round.
Which one do I need — metric or inch?
The first decision is not a fitting at all: it is the system the drawing was issued under. Ferrule and body are machined to one exact tube OD, so the tube size on the drawing already answers the question.
| What you are choosing | Metric | Fractional inch | What actually decides it |
|---|---|---|---|
| Tube OD | 6–25 mm core; 12 mm is 12.00 mm | 1/2 inch is 12.7 mm | The unit printed on the drawing, never a conversion |
| Ferrule-to-body fit | Machined to one exact millimetre OD | Machined to one exact inch OD | Whether ferrule and body were cut for the same tube OD |
| Size ladder | DIN 2353 L, S and LL | Sixteenths and dash numbers | The standard the drawing was issued under |
| Tail thread | M fine per ISO 261, or G | The plant’s inch thread | The thread standard the plant actually runs |
| Where the systems meet | Transition fitting | Transition fitting | A purpose-built part, not a near-size substitution |
The near-miss trap is the first lesson of the millimetre system. Put a 12 mm tube in a 1/2 inch fitting and the ferrule meets a surface roughly 0.7 mm oversize.
The bite geometry cannot close and the seal lands on a gap, so leak or blow-out risk arrives with pressure. Maker guidance is unambiguous: ferrules and bodies are machined for one exact tube OD, and close does not mean compatible.
The rule runs the other direction too: a metric ferrule on inch tubing seats on nothing. The correct bridge is a purpose-built transition fitting, not optimism. The dash-number system has its own mirror of this trap, covered in dash numbers on drawings.
Before the line is committed, confirm:
- The tube OD as printed, in its own unit.
- Whether ferrule and body were cut for that same OD.
- The standard the drawing was issued under — DIN 2353 or the inch system.
- The tail thread the plant actually runs.
- Whether the two systems must meet anywhere; if so, a transition fitting.
When fitting and tube come from different systems, the symptom shows up at pressure:
| Symptom | Most likely cause | What to change |
|---|---|---|
| Seepage at the bite as pressure rises | 12 mm tube in a 1/2 inch body, roughly 0.7 mm oversize | Match the tube OD to the ferrule, or fit a transition |
| Bite lands off-centre, tube mark uneven | Body machined for a different exact OD | Replace with a body cut for this tube OD |
| Seal never closes, ferrule seats on nothing | Metric ferrule on inch tubing | Purpose-built metric-to-inch transition fitting |
| Blow-out at pressure instead of a weep | The gap the bite cannot close | Strip the joint and rebuild on matched components |
What sizes are in the 6–25 mm range?
The working metric instrument range is eight sizes. Maker catalogs extend the ladder both ways — one major catalog runs from 2 to 38 mm — so treat the eight as the common core, not the complete list.
- 6 mm OD
- 8 mm OD
- 10 mm OD
- 12 mm OD — the stock example, 12 × 1.5 and 12 × 2
- 15 mm OD — DIN-native
- 18 mm OD
- 22 mm OD — DIN-native
- 25 mm OD — top of the common instrument core
Walls pair conventionally at 1.0, 1.5 and 2.0 mm, with 12 × 1.5 and 12 × 2 the stock examples every tubing table carries. The ordering grammar mirrors the inch world’s: OD × wall for tube, thread standard and size for the tail.
The compression fittings range covers both systems, and the inch-side counterpart of this post is metric vs fractional tube sizes.
The metric ladder names every fitting after the tube’s outside diameter, never its bore: 12L means 12 mm OD, light series. The OD picks the catalog row, and the wall only has to sit inside the ferrule’s grip range.
How OD sizing, wall and the DIN size names interact is laid out in compression fitting sizes: OD vs ID.
Which thread tail, M or G?
Metric fittings carry two thread families on the same bodies, and the RFQ should say which. Metric fine threads follow the ISO 261 ladder: M12×1.5 for 6 and 8 mm tube nuts in the DIN system, stepping up through M14×1.5, M16×1.5 and M18×1.5 as the tube grows.
That metric fine tail is the DIN 2353 native one. G threads — the parallel BSPP form — appear on the same metric bodies where the plant standard is BSP, and maker catalogs list metric-tube fittings with G tails as standard variants.
| Thread family | Sizes named in this post | How it seals | What actually decides it |
|---|---|---|---|
| Metric fine, ISO 261 | M12×1.5, M14×1.5, M16×1.5, M18×1.5 | At the face | The drawing is issued to the DIN system |
| G, parallel BSPP | G1/4 | At the face | The plant’s thread standard, stated on the RFQ |
The sealing logic follows the thread. Metric fine and G threads on port studs both seal at the face, per the BSP thread seal logic that parallel threads never seal on the flank.
The nut-to-body joint is the compression mechanism itself: the 24° cone bite covered in bite-type fittings explained.
Why do 15 and 22 mm fittings exist?
15 and 22 mm have no inch near-equivalent at all, and the DIN 2353 size ladder is why they exist. It is the metric-native standard, now mirrored by ISO 8434-1.
Its L series runs 6, 8, 10, 12, 15, 18, 22, 28, 35 and 42 mm. The S series for heavier wall runs 6–38 mm, and the LL light series covers 4–12 mm.
The ladder is deliberately decoupled from the inch world’s sixteenths. A European drawing quoting 15 mm or 22 mm is quoting native sizes, not conversions — and the matching ferrule exists only in the metric catalog.
Size walk for DIN-native hardware is the same pressure-chart territory as every bite-type fitting: the DIN 2353 pressure chart carries the L and S series working pressures.
How do I write the RFQ line?
Four fields carry the whole line, and a fifth step reads it back before it leaves the desk. A line missing any one of them comes back as a clarification round. The two-line RFQ habit that keeps inch lines clean does the same work here.
- Step 1 — tube OD × wall. In millimetres, both numbers:
12 × 1.5, not12 mm tube. - Step 2 — series. DIN L or S where the standard applies, or the maker’s metric series name.
- Step 3 — tail thread.
M12×1.5orG1/4: the thread family is a decision, not a default. - Step 4 — system note. Metric line, metric ferrules; the words that prevent an inch-fitting substitution.
- Step 5 — read it back. OD, wall, series, thread standard. Any field that is a conversion rather than a printed size is not ready.
FAQ
Can I put a metric ferrule on inch tubing?
No. The ferrule bites one exact millimetre OD, and the nearest inch size differs by four to seven tenths of a millimetre. The bite lands off-centre and the seal never closes; use a transition fitting.
What are the common metric compression fitting sizes?
The instrument core is 6, 8, 10, 12, 15, 18, 22 and 25 mm OD, with catalogs extending from 2 to 38 mm. Those eight are the working set; walls run 1.0, 1.5 and 2.0 mm.
Is a 12 mm fitting the same as 1/2 inch?
No. 12 mm is 12.00 mm and 1/2 inch is 12.7 mm, and a ferrule machined for one cannot close the 0.7 mm between them. Use a transition fitting where the systems must meet.
What thread is on a metric compression fitting?
Two families: metric fine per the ISO 261 ladder — M12×1.5 and upward in the DIN 2353 system — and G threads as a catalogued variant on the same bodies. Both seal at the face; the choice belongs on the RFQ.
Why do 15 mm and 22 mm fittings exist?
The DIN 2353 / ISO 8434-1 ladder says so: its L series runs 6, 8, 10, 12, 15, 18, 22, 28, 35 and 42 mm, decoupled from the inch world’s sixteenths. They are native metric sizes, not conversions.



