Pipe schedule numbers are a wall-thickness series, not a measurement and not a pressure rating. Schedule 40 and Schedule 80 on the same NPS share one outside diameter and differ only in wall. So the wall moves, the bore moves with it, and the OD does not — that is the whole of it. Read the chart for the wall, then check the wall against the thread.
Key takeaways
- Schedule is a wall-thickness series designation: same NPS, same OD, higher schedule = thicker wall, smaller bore.
- NPS is a name, not a measurement — NPS 1/2 pipe is 0.840 in OD whatever the schedule.
- In the small-bore range, Schedule 40 matches the STD wall and Schedule 80 matches XS (XS equivalence holds through NPS 8).
- Schedule is not a pressure class: the same schedule rates differently with material, diameter and code.
- Stainless pipe uses the S-suffix schedules (5S/10S/40S/80S); thread cutting needs enough wall under the thread — thin schedules cannot hold it.
Which one do I need?
The end prep decides before the pressure does. A threaded joint needs wall under the thread; a welded or compression joint does not. Fix the end prep first, then read the wall off the chart at that NPS.
| Line requirement | Series to quote | Why it holds | What actually decides |
|---|---|---|---|
| Threaded joint, small bore | 40S or 80S | The NPT cut needs full-depth wall beneath it | End prep |
| Welded, beveled or compression end | 5S or 10S is usable | No thread is cut, so the thin wall has nothing to lose | End prep |
| More pressure margin at the same OD | 80S over 40S | Thicker wall adds margin, not a class | Material, diameter, temperature and design code |
Two consequences follow the table. The fitting does not change with the schedule, because the OD does not change. The bore and the flow area do change, and nothing about the schedule number certifies a pressure class.
What does the schedule number actually mean?
A schedule is a standardized series index for wall thickness, defined by ASME B36.10. Pick an NPS and the OD is fixed — NPS 1/2 is 0.840 in (21.3 mm) whether the wall is 0.109 or 0.147 in — and the schedule selects the wall. Our printable pipe schedule chart covers the small-bore range in the values procurement actually quotes:
| NPS | Actual OD (in) | OD (mm) | Sch 10 wall (in) | Sch 40 wall (in) | Sch 80 wall (in) |
|---|---|---|---|---|---|
| 1/8 | 0.405 | 10.29 | 0.049 | 0.068 | 0.095 |
| 1/4 | 0.540 | 13.72 | 0.065 | 0.088 | 0.119 |
| 3/8 | 0.675 | 17.15 | 0.065 | 0.091 | 0.126 |
| 1/2 | 0.840 | 21.34 | 0.083 | 0.109 | 0.147 |
| 3/4 | 1.050 | 26.67 | 0.083 | 0.113 | 0.154 |
| 1 | 1.315 | 33.40 | 0.109 | 0.133 | 0.179 |
| 1-1/4 | 1.660 | 42.16 | 0.109 | 0.140 | 0.191 |
| 1-1/2 | 1.900 | 48.26 | 0.109 | 0.145 | 0.200 |
| 2 | 2.375 | 60.33 | 0.109 | 0.154 | 0.218 |
Full printable version: pipe schedule chart
In this small-bore range Schedule 40 is the STD (standard) wall and Schedule 80 is the XS (extra-strong) wall. XS equivalence holds through NPS 8, then diverges at NPS 10, where XS is 0.500 in and Schedule 80 is 0.594 in.
Values above are published B36.10 nominal figures, reproduced from the chart without recomputation.
The fixed OD is a compatibility rule, not a curiosity. Pipe sizes were locked generations ago so that fittings, flanges and threads would interchange whatever the wall — which is why the NPS name stopped meaning any measured diameter below NPS 14. Only the bore moves with the wall: a Schedule 80 1 in pipe carries noticeably less flow area than its Schedule 40 sibling.
That ordering logic is the pipe-versus-tube split, pipe by NPS and schedule against tube by OD and wall, covered in pipe vs tube. The dash system is the mirror case, where the number does measure something (dash size chart).
Beware the acronym collision too: the same NPS that names nominal pipe size also names National Pipe Straight, the parallel pipe-thread series. One is a dimension system, the other a thread form, and NPT vs NPS threads separates the two meanings.
Does a thicker wall raise the pressure rating?
No. Schedule is not a pressure class. The same Schedule 80 wall rates very differently in carbon steel and stainless, at different diameters and temperatures, under different design codes. Rating is a calculation from material allowables, diameter and temperature, not a lookup on the schedule index.
Thicker wall buys margin; it does not certify it. Schedule 80 in one material can out-rate Schedule 160 in another at some sizes, which is the clearest proof that the number is a wall, not a class.
Which schedules can I thread?
The rule is wall under the thread. The NPT form cuts to a depth of about 0.8 times the thread pitch, and the wall must survive that cut with margin. Thin schedules — 5S, 10S, and some 40 in small sizes — cannot hold full-depth threads at all.
That is why threaded stainless work runs 40S and 80S. The thread form itself does not change: threaded Schedule 40 and Schedule 80 of the same NPS take the same fitting and seal the same way. The heavier wall leaves more material beneath the same thread, resisting deformation and mechanical damage.
When a joint fails, the wall is usually the reason and the schedule number is usually the alibi.
| Symptom | Most likely cause | What to change |
|---|---|---|
| Thread strips, or the joint weeps | Wall too thin to hold the full-depth NPT cut — 5S, 10S, some 40 in small sizes | 40S or 80S; where no wall is there, a welded or compression end |
| Fitting will not go onto the pipe | Schedule read as a change of OD | Quote by NPS — the OD is fixed and only the bore moves |
| Flow below what was sized | Heavier schedule at the same NPS | Read the wall at that NPS and step to a lighter series where the thread allows |
| Quote comes back with the wrong wall | Bare “Schedule 40” on a stainless line | Write NPS, 40S, and the standard: B36.10 or B36.19 |
| Rating assumed from the schedule | Schedule treated as a pressure class | Calculate from material, diameter, temperature and design code |
| Threads will not mate at assembly | NPS read as a thread standard | Run the bench test before the line is made up |
Identification before assembly follows the bench test.
What changes on stainless pipe?
Stainless pipe follows ASME B36.19 and its own schedule family with an S suffix: 5S, 10S, 40S, 80S. The S distinguishes the stainless series from the carbon schedules. It does not mean the walls are uniformly thinner, whatever the shorthand says.
Through about NPS 10, the 40S and 80S walls are identical to their carbon 40 and 80 counterparts. The series diverges at larger sizes, and it is the 5S and 10S walls that are thinner than anything B36.10 offers. In the small-bore instrument and process range above, 40S behaves as 40.
So when the RFQ says “stainless pipe, 1 in, Schedule 40,” the honest write is 1 in NPS, 40S, with the standard named.
How do I write the line on the RFQ?
Five steps carry the order, and the wall falls out of them.
Step 1 — write NPS and schedule together. 1/2 NPS Sch 40S, never the bare name. The name alone does not fix the wall.
Step 2 — name the standard. ASME B36.10 or B36.19 as applicable, because the same schedule number lives in both series.
Step 3 — state the end prep. Threaded, beveled for weld, or plain. This is the line that decides whether a thin series is even on the table.
Step 4 — state material and test requirements. Grade, certificate type, any hydro or NDT.
Step 5 — check the wall at that NPS against the chart. 0.109 in and 0.147 in are the same NPS 1/2 and different orders.
Before the line goes out, confirm:
- NPS stated, not a measured diameter
- Schedule written with the S suffix on stainless
- Standard named — B36.10 or B36.19
- Wall checked against the 0.8 × pitch thread depth where the joint is threaded
- End prep stated: threaded, beveled or plain
- Grade, certificate type and test requirements stated
- Fitting quoted by NPS, since the schedule does not change it
FAQ
Is Schedule 80 always stronger?
Thicker wall adds pressure margin, but pressure rating depends on material, diameter, temperature and design code. Schedule alone certifies none of it. Schedule 80 in one material can out-rate Schedule 160 in another at some sizes.
Why does the OD stay the same when the wall changes?
Compatibility. The OD was standardized so fittings, flanges and threads interchange across walls: Schedule 80 threads into the same fitting as Schedule 40, and only the bore moves. The NPS name stopped meaning a diameter below NPS 14.
What does the S in Schedule 40S mean?
ASME B36.19, the stainless series. S-suffix schedules belong to stainless pipe, not the carbon schedules of B36.10. Through about NPS 10 the 40S and 80S walls match their carbon namesakes; 5S and 10S are thinner than anything B36.10 offers.
Can I thread Schedule 10 stainless pipe?
Generally no. The NPT form cuts to roughly 0.8 times the pitch, and a Schedule 10 wall cannot hold a full-depth thread with margin. Threaded stainless runs 40S and 80S; below those, use welded or compression ends.
Is Schedule 40 the same as STD?
Through NPS 10, yes. XS equals Schedule 80 through NPS 8, diverging at NPS 10, where XS is 0.500 in and Schedule 80 is 0.594 in. Above those sizes, read the wall table.



